Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Woodcraft Grinder

Posts

Re: Woodcraft Grinder

#26

Re: Woodcraft Grinder---LONG

john lucas

>Galen My mother bought a Chevy new and it had a rattle. They looked for it for about 3 months off and on until she really complained loudly. They found a coke bottle inside the rear fender. Had to actually cut some welds to get it out. It had apparently been left there by a worker assembling the car.

Re: Woodcraft Grinder

#27

Mike Stafford

I agree!!!

Mike Stafford

>I have never been satisfied with any of the Woodcraft grinders I have used. I don't believe I would buy one.

I have a Baldor that I bought long before I was turning that is a "Cadillac" and is a delight to use. If I have one complaint is that it continues to revolve for a long time after it is turned off. I also have two long shaft Baldor buffers, a 6" and an 8". Both are a pleasure.

I don't know the difference between all the different wheels but I am using blue wheels now and they seem to do a good job. I never liked how quickly the white wheels would glaze over and need redressing.

When it comes to power tools I believe you get what you pay for in most instances.

Re: Woodcraft Grinder

#28

Re: Woodcraft Grinder -Replace the Bearings

Dave (PacNW)

>Reading your original post, You stated you had used the grinder for several years. I suspect that the Chinese bearings are starting to go (wear out) causing the grinder to vibrate very slightly and causing the bolts to loosen. I would replace them with a good quality American Made sealed bearing set. I did this last year and after re-balancing my Norton 3x wheels, the grinder will coast for over 5 minutes after turning it off. It is also much smoother to use.

Just 6 cents worth (adjusted for inflation!)

Dave (PacNW)

Re: Woodcraft Grinder

#29

Re: Woodcraft Grinder

Fred Holder

>Hello Barbara,

I've been using the Woodcraft grinder for over 10 years, not the first one but the second one is still working very well. The first one simply gave up and died after about 4 or 5 years. The second one is still working well, but much better since I put diamond wheels from Andre Martel on it. With the diamond wheels, it runs for a long time after it is turned off. Much better than the white wheels that came with the grinder. One does have to remove the guards to use the 1-1/2 wide diamond wheels. The addition of the diamond eliminated any vibration that I had, gave me a 1-1/2 inch wide wheel to sharpen my tools on, and made that $89.00 grinder from Woodcraft a $400.00 grinder. The 360 grit wheel that I have on the right side gives a finish similar to the Tormek.

Re: Woodcraft Grinder

#30

Re: Woodcraft Grinder -Replace the Bearings

Barbara Gill

>Actually the vibration was from the loose nuts. I tightened them and the vibration is gone.

Re: Woodcraft Grinder

#31

Re: Woodcraft Grinder

Barbara Gill

>That is very interesting Fred. I will look into it. When I turn this grinder off it too will continue to spin for a long time.

Re: Woodcraft Grinder

#32

$700 For a Grinder?...Sheesh

Wally Dickerman in Arizona

>My present grinder, a Woodcraft, has run very smoothly since the day I bought it several years ago for under $100. I can't imagine what another $600 in a grinder would do for me.

I do some of my grinding, tool reshaping etc. on a 1 inch belt sander using a zircon belt. Does a great job.

Wally

Re: Woodcraft Grinder

#33

Re: Woodcraft Grinder returned

Jorge Casta�eda

>Carol,

I had a Delta that got stolen in a job, could not find another around here, so one day at the Borg i spotted an 8" Ryobi around $50.00. I works very well and the only thing about it is that it takes forever to stop.

Check them out

Jorge

Re: Woodcraft Grinder

#34

Re: Woodcraft Grinder

Galen Vetterick

>Fred

That's like buying a Chevy and turning it into a Cadillac! :>)

Re: Woodcraft Grinder

#35

OK John I'll come clean

Galen Vetterick

>When I was 17 years old and worked on the assembly line at a Purolator plant I must have gotten bored on the night shift and put a dead rat in one of the filter boxes. Always wondered who got that one!

I was a baaaad boy!!!!!!

Wonder now if the creator made me pay it back many times over for that one.

Galen

Re: Woodcraft Grinder

#36

Have the balancer flanges slipped?

Russ Fairfield

>I done see where anyone has suggested that you true and rebalance the grinding wheels. If the balancing flanges slip[ped on the wheel, it can be very out of balance.

Re: Woodcraft Grinder

#37

Re: Woodcraft Grinder returned

Carol Reed

>RPM?

Orange or blue borg?

Re: Woodcraft Grinder

#38

They're out there

Rik in WI

>I picked up an 8" high speed Baldor in excellent condition for $400 ($300 + $100 s/h) within the last month or two. Well worth the wait.

Re: Woodcraft Grinder

#39

The Delta 23-725 grinder

Carol Reed

>Unfortunately Delta has discontinued this machine. It is exactly what I wanted. Heavy, slow speed. I have wheels. I just need to find something to put them on!

Wonder if there is one on a shelf somewhere? I'm watching craigslist and searching Google.

Re: Woodcraft Grinder

#40

Re: Have the balancer flanges slipped?

Barbara Gill, Remlik VA

>Yep, I thought of that possibility. The weights seem to be nice and tight. If the problem continues I will take the wheels off and check them.

Right now I am still walking across "wetlands" to my shop. Yesterday was cloudy and cold with a strong wind and I became a weather whimp.

Re: Woodcraft Grinder

#41

Rob Wallace

Re: Woodcraft Grinder

Rob Wallace

>Fred holder wrote:

"The addition of the diamond eliminated any vibration that I had, gave me a 1-1/2 inch wide wheel to sharpen my tools on, and made that $89.00 grinder from Woodcraft a $400.00 grinder."

Does that mean that the Martel diamond wheels cost you $ 311?

( Just skeptical about machine quality "magical" transformations...... :\ )

Rob Wallace

Re: Woodcraft Grinder

#42

Re: Woodcraft Grinder returned

Jorge Casta�eda

>Carol,

3500 rpm, at the orange Borg.

I prefer the 3500 over the slower ones, best results.

Jorge

Re: Woodcraft Grinder

#43

Re: Woodcraft Grinder

Jorge Casta�eda

>Rob,

I think machined wheels will be a lot less prone to unbalance than the ones made from abrasives and adhesive or whatever means to make them.

I've tried the grey ones that came with my grinders, the white ones and now the blue ones and all of them where imbalanced, the white ones the worst, one of the blue ones cannot balance even with the Oneway balancer, so this post is making me wonder, what if?...uhmmm

Jorge

Re: Woodcraft Grinder

#44

Don Geiger

Re: The Delta 23-725 grinder

Don Geiger

>When I recommended the Delta grinder to you on 2/13, I didn't realize it had been discontinued. If you can find a used one and it runs, it will probably be fine. These grinders are well built. I used to work in an electric motor shop, rebuilding and rewinding motors. I became quite familiar with quality motors and the Delta 23-725 fits that mold quite well.

Don

Re: Woodcraft Grinder

#45

Re: The Delta 23-725 grinder

Carol Reed

>I'm looking, Don.

Meanwhile I am going to use my 12" disk sander that I had with my Shopsmith, now long gone. Just hang the disk directly on the motor shaft and mount the Wolverine under it. That may work well enough that I'll skip the grinder!

Re: Woodcraft Grinder

#46

Re: The Delta 23-725 grinder

John Jordan

>Carol, I don't know if it's the Delta you want, but I was at Lowes today and they have an 8" Variable speed Delta on closeout for $118. It has a nice 60 grit wheel on one side, and some sort of tool-less nut, sort of a large folding wingnut. The flanges are large, and thick. It's a nice looking grinder, but it's just sitting there, so who knows. I think I have probably used them, but I don't pay much attention when I'm traveling, unless they're awful.

Maybe a Lowes near you has them.

John

Re: Woodcraft Grinder

#47

Re: The Delta 23-725 grinder

Carol Reed

>Not the same one, John. The discontinued model was 115#'s or so.

Re: Woodcraft Grinder

#48

Re: The Delta 23-725 grinder

Jennifer@Indy.USA

>John, the one Carol is talking about is like the ones that are Marc Adams. Not Baldors but okay. They are much heavier duty than the one you saw at Lowes which is what I have. I've had trouble with the on off switch, had to replace it and also the lamp fell apart and I had to replace it too. The white wheel isn't bad that comes with it. The gray one I tossed. I did mount Oneway wheel balancers on it to help it run a bit smoother. FYI I never use the thing on anything but the slowest speed so the variable for me anyway is a mute point.

Jen

Re: Woodcraft Grinder

#49

Re: The Delta 23-725 grinder

Jim Shaver

>yeah, Those One Way Balancers are awesome.......... $$

Re: Woodcraft Grinder

#50

Rob Wallace

THANK YOU!  THANK YOU! THANK YOU!

Rob Wallace

>Thanks to everyone who contributed to this thread! Over the past few days I've been looking around on the web for 8" slow speed grinders and agree that they are uncommon beasts, made even more rare by the demise of the Woodcraft 8" slow Speed Grinder.

Today I was fortunate enough to find a Delta 23-725 in stock (their last unit!) at one of our local tool suppliers. Because it was discontinued, they let me buy the "New Old Stock" grinder for $ 175 (+ tax) [Regular price about $ 200]. This is a brand new grinder, in the original box, with manual, accessories, etc. - I feel really lucky to have found this! Thanks to Don Geiger and others who made the recommendation about this tool! I purchased it today on plastic and I pick it up next week!

To others searching for one of these grinders, keep looking!

Cheers,

Rob Wallace