New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

"What Are You Working On"

Posts

Re: "What Are You Working On"

#54

Thrift..

David Weaver

Thrift caused me to want to figure out a way to taper the irons, the reality of how little is needed just makes it convenient.

I made the first pair with straight irons thinking that I could get away with it but they are very hard to get out. The taper in the irons is applied in a small jig where an iron is tacked to the jig with two dots of CA and retained in a routed groove about a 16th deep. No need to wait for the CA to dry, just get it against the belt with the sander vertical and with the tang as the trailing edge and the iron heats up in abrasion and the CA dries instantly. When done, tap the jig on the bench and the iron falls off. It is an inelegant method that ame out of cheap despiration, but if the jig is an inch wider than the iron on both sides, one cannot unevenly taper the iron laterally.

Anyway, I'd guess that the taper at the tang end is probably less than a 32nd and in the business area where it's actually held against the bed less than that by a fair amount and almost none at all on the face of the iron except for a small area where the tang and face meet. I am sure that the taper is not linear, but instead convex which causes all sorts of thoughts of failure of method to go through your head, but successful practice beats feared theoretical failure.

Maybe I will videotape it the next time I make a pair, or take pictures. It will horrify machinists.

It makes an enormous difference in extracting the wedge from the plane. Advance the iron, grab the wedge by hand, tap the back of the plane and it's out. Without the taper, it was a battle. One that combined with a change in humidity might cause the loss of a wedge.

Re: "What Are You Working On"

#55

For some of us...

David Weaver

... I wish I could say no, but my production of gobs of imprecise work would say otherwise.

Re: "What Are You Working On"

#56

A pair of night stands

Paul Dzioba

Nice work Bill. How do you plan on finishing your drawer fronts? If I remember correctly, you like to stain walnut with your own stain made with earth pigments. Wouldn’t that also stain the line and berry wood?


The night stands are being made from cherry. I just shot from the hip with these. They are sized to fit my bedroom and the width of the cherry stock I had on hand.

Paul Dzioba

Re: "What Are You Working On"

#57

Re: A pair of night stands

Bill Tindall, E.TN.

I like your pattern on the bottom. I would like to use bases like this more but my designs never look very good and I go on to some other bottom such as bun feet. Nice joints to the right.

As for finishing my drawer fronts, well, that remains to be seen. I have lots of practice pieces to experiment with. On a practice piece made with maple string I was able to sand the front to a higher than normal degree which rendered the maple "stain repellent". The holly is softer so we shall see what can be done. In any case 96 berries need to be "artfully", if not whimsically, installed and that is waiting on a back ordered plug cutter. I may not wait and make one from a piece of tubing.

Re: "What Are You Working On"

#58

Re: A pair of night stands

roger lance

As if all this delicate work has not taken its toll on you, I've seen some makers use a small artist brush to first cover their lines with a coating of shellac to prevent the stain from over darkening the holly. This is where an artistic, eager grand-daughter would be very handy indeed.....just need one about 16 -18 with great eyes and a steady hand.

Re: "What Are You Working On"

#59

Re: How sweet it is!

TomD

That plane is very interesting, is that a type you recognize. It looks so much like a plane that might have been made in 1980 from instructions in FWW, or some such. The vertical lams, the roundovers, the razee. The cross pin, the beef of the wedge, and the wood.

Re: "What Are You Working On"

#60

Re: To berry or not to berry.

William Duffield

I'm afraid the berries are a "must" in this case. The overriding consideration here is that Bill's magnificent chest is a reproduction of a piece in a very specific tradition, from Chester County Pennsylvania. The decoration is usually called "line and berry." In all the examples I've seen, all the inlaid strings that do not terminate at an intersection with another string terminate with a grouping of berries. There are usually three in a group, but sometimes one or two. The case pieces, including chests of drawers, spice chests and boxes, sometimes have bracket feet, and sometimes have turned bun feet. The decorated panels, including doors, drawer fronts and box fronts are often bordered with stringing, as in Bill's example, and often with herringbone veneer.

This style is documented in Furniture and Its Makers of Chester County, Pennsylvania by Margaret Berwind Schiffer, and Line and Berry Inlaid Furniture: A Regional Craft Tradition in Pennsylvania, 1862-1790, by Lee Ellen Griffith and Dr. Henry Glassey. IIRC, Bill told me the latter was a doctoral thesis paper.

Re: "What Are You Working On"

#61

Busy busy busy...

James Watriss

So, the current, and ongoing project, is that I'm now a Dad. It's weird, and not really as weird as I thought, if that makes any sense at all. I'm blessed with a great and level headed wife who makes it easy to figure out new routines around all of that.

The other new-ish thing is that I've been working part time at a shop that specializes in repairing caned chairs. The logic being, once I'm up to speed, I can re-weave seats at home on days when I'm home with the kid. We'll see how that theory stands up in practice, but for now, it's pretty cool. I'm still surprised at the number of different ways people have found to use caning in furniture, and how much of it comes through the door.

Anyway, I hear a diaper calling my name...

(Is it weird that my day to day instinct to work efficiently in the shop has influenced the way I've set up and used the changing area?)


img

Re: "What Are You Working On"

#62

Re: Busy busy busy...

David Weaver

Congratulations. Your theory of work will be OK until the kid is mobile. And once walking, all work will have to occur during nap time (kids have a great ability to ignore noise that would be uninteresting to them. I can cut mortises right below my daughter's bedroom, and no problems).

Re: "What Are You Working On"

#63

Re: How sweet it is!

Derek Cohen (in Perth, Australia)

Hi Tom

Yes, I agree. Not an old plane. Also not a "Krenov" laminated style - not a common or modern design. It is made in two sections with the join down the centre.

There is too much work here for someone to have made it for sale - and why sell it in Australia, that is not the best market place for this plane? Anyway, it is a nice memento, and I use it occasionally.

Regards from Perth

Derek

Re: "What Are You Working On"

#64

babies with hair are "better"

Bill Tindall, E.TN.

or at least better to admire. Thanks for the picture.

I went to a caning lecture and it was described that the practice is very old. Later I attended a King Tut exhibit and sure enough the chair in his tomb was caned just as in modern times. I had an uncle that caned. It was fascinating to watch.

Re: "What Are You Working On"

#65

Thank you for asking Derek

Patrick Gibbons

I've been trying to clean and arrange my shop and get some light fixtures put up. My sister won a forge (a long story) that she's giving me and I need to put it somewhere in the shop. I am making a knife that I hope to finish soon. Then there's income tax, cleaning the office... I have all kinds of excuses for not making anything. I have a lot of good intentions though.

Re: "What Are You Working On"

#66

Re: A pair of night stands

Patrick Gibbons

Paul I really like your night stands. The bevel at the top really lightens the look. What are you planning to use for hardware?

Re: "What Are You Working On"

#67

Paul....a question about your bench....

roger lance

I like your night stands....but I also noticed your work bench.....it appears that you are able to work all around the bench and that you might have more than the standard two vises....if possible would you show more about this bench ??....thanks.

Re: "What Are You Working On"

#68

Re: A pair of night stands *LINK*

Paul Dzioba

In my eye the top still looks a little heavy, I might plane a little more of the thickness out. The bevel will become a cove. You probably can't tell from the picture, one top actually is a cove made with a #18 hollow plane, the other awaits. I am going with a Sheraton flower knob purchased through Lee Valley.


It probably is not appropriate but I liked the way it looked, elegant but not too outlandish.

Paul Dzioba


Sheraton knobs at Lee Valley

Re: "What Are You Working On"

#69

Re: Paul....a question about your bench....

Paul Dzioba

Roger you are correct about the bench being walk around, I find that advantageous. The only disadvantage that I see to that is that if it were secured to a wall it would be a little more solid. My bench flexes a little during heavy planning, I plan on adding a little bracing. There is only one simple twin screw vice. When I get a chance, I will post pictures of my bench. I find it interesting to see other benches and work solutions.

Paul Dzioba

Re: "What Are You Working On"

#70

How did you make the recesses for the pens?

wilbur

Nice work!

Re: "What Are You Working On"

#71

Re: A pair of night stands

William Duffield

What advantages do you find in installing the drawer runners before the drawer blades?

Re: "What Are You Working On"

#72

Re: To berry or not to berry. *LINK*

William Duffield

Oops, and some minor corrections: Bill already provided most of this info in response to a question on the main message board.

http://www.woodcentral.com/woodworking/forum/messages.pl/page/1/md/read/id/465146/sbj/line-and-berry-strings-done-at-last/

The most important point he makes, at least to my way of thinking, is that this is not a reproduction of any one particular piece.

I'm glad I looked over on Messages before I spent any more time searching the reference materials for a perfect match for Bill's tulips and the chest he put them on. :) So, I still don't know if he created the line and berry design from scratch or used an old example. If it is an interpretation, IMHO, he got it right. It is stylistically correct.

I also don't like to make exact reproductions. Unlike Stickley, furniture makers in the 18th century weren't using cookie cutters, so each piece of furniture was unique. I like to think, "What would ______ have built next, to fill the needs of his next customer?" I probably won't get it right, but it's a whole lot more fun that trying to meet the needs of his previous customer. I will use power tools where they are appropriate, but won't compromise the style of the piece, and I will use modern materials and even modern joinery methods, where there is evidence of failures in the originals, and where the new stuff won't show.

Maybe we should start a new thread: How far do you stray from the original when you make a reproduction?

Re: "What Are You Working On"

#73

Re: A pair of night stands

Paul Dzioba

Bill!

It would have been too logical to do that! I have always glued the main carcass together first without the drawer blades. Glue up is a frantic time for me no matter how much I prepare for it. I have a little more time if I glue in stages to ensure the carcass is square and not racked before the glue starts to set. Let us just say I have had a few less than optimal results from complicated glue up. I don’t even cut the dovetails for the blades until the carcass is glued. In a full size piece I would install the runners after the drawer blades but these night stands are narrow and I did not have the room to hammer the nails.

Regards,

Paul

Re: "What Are You Working On"

#74

Very cool!

John in NM

I like them, nice work David!

Re: "What Are You Working On"

#75

Re: I have a tool for that

William Duffield

Nailing in the runners is traditional, but with modern screws and screw drivers…well, they won't be seen, and will be easier to remove and replace when they get worn out. Of course, there have been right angle screwdrivers for a hundred years or so that work well, and they make palm held pneumatic hammers, but my favorite is like this one, but with a smaller battery, with right angle and offset chucks. I just can't fold my body up into tiny cabinets like I used to, or unfold it again when I've finished fastening.



I should probably look for a Millers Falls #737 right angle brace. I wouldn't have to worry about the battery running down when least expected.