New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Shooting End Grain: How Heavy A Cut Do You Take?

Posts

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#26

Re: The need is another variable

Derek Cohen (in Perth, Australia)

Hi Bill

There is another factor. Do you generally shoot ends that are 3/4" thick, or just use a block plane free hand on such?

Regards from Vegas (just connected, and now off to explore)

Derek

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#27

Re: The need is another variable

Bill Tindall, E.Tn.

It is likely my need and application is so removed form most on this Forum that an answer would be misleading. Unlike Wiley my shooting needs are normally best met by getting on with it. I will use a shooting board and low angle heavy plane (LV low angle was recommended as best and after I bought it I do not dispute this recommendation) any time I can. And I have at it with quick repetitive strokes as seep as the plane will allow. If the piece to be hacked at doesn't lend itself to positioning on the shooting board then I might use what ever is close at hand, LV low angle, or my favored #5. I find a block plane the least favorite choice unless the need is small and precise. It lacks sufficient mass to remove wood quickly.

Caveat- I am almost never planing end grain for appearance, always to remove wood as efficiently as possible.

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#28

the best thing about Vegas

Bill Tindall, E.Tn.

Is that it is easy to leave and go to Bryce or Grand Canyon or tour the dam/bridge. The "Bling" is to be experienced once I suppose. Derek are you visiting any place in the US we can be proud of showing off?

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#29

Re: What a drive by gloat !!.......

roger lance

I'd have to count myself among those that have been greatly influenced by Norm.....at first, because he was a building contractor as was my dad.....I've watched Norm from his very first appearance on This Old House and still do.....that group on This Old House is as good as it gets.....

secondly, by the New Yankee Workshop.....he was my first ww teacher and even though I think I've learned other methods and techniques that my teacher did not demonstrate, I still owe him a debt of gratitude....woodworking would not be where it is without him.

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#30

Another factor

Ron Harper

I take thin shavings. If i have the work in a vise to plane the end a block plane is fine. If I am using a shooting board I have to work very hard tomkeepthebtop edge of the block plane from tilting inward. That is why I almost use my 605 1/2 for my shootong board. It minds its manners

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#31

You may be looking at the wrong standard

Ron Harper

When I shoot end grain, I am looking for a square, plumb, shiny end of a board. I look at what is left on the wood, not what came off?

Really is not meant as a smart ass comment.

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#32

This must be Hell!

Derek Cohen (in Perth, Australia)

My only reasons for being in Vegas are (1) my wife said we had to do it once, and (2) my wife said we had to do it once.

Tomorrow we head for the Grand Canyon.

Vegas is noisy (there is no escape from the "music" which blares everywhere), crowded, filled with expensive clothing stores for women (which is like a candle for a moth with Lynndy), I cannot find a decent tool shop anywhere and even the hotel fridge tried to lay a bet with me. I have eaten far too much good food in the past 10 days (I blame on the good company I kept), and would now kill for a salad and am, instead, surrounded by every fast food imaginable.

Dying in Vegas

Derek

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#33

Re: This must be Hell!

roger lance

Derek....While in Vegas, you might be tempted to check if someone is a "Sheila" or not like Dundee did.....don't.

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#34

One of the odd things about Vegas...

Bill Houghton, Sebastopol, CA

...is that it's right in the middle of some of the more austere, but lovely for those who like it, country in the U.S. - and not far from some stunning places, as Bill Tindall points out.

It is not on my personal list of reasons to be proud of the West.

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#35

food

Bill Tindall, E.Tn.

Everywhere in Vegas has buffets with sumptuous salad fixins.

Bryce Canyon is worth the visit if the weather is permitting (it is high elevation and colder than the surrounding area.) Drive there is also nice. The pictures of it look phony but indeed that is how it looks. There are motels in the area and restaurants run by wholesome Mormon families making simple good food. Any Mexican place on the way is likely very good. Do walk down the trail among the spires to experience the geology.

The dam is also worth a visit and it is close by.

I am not smitten by Death Valley but most are.

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#36

Death Valley

John in NM

My wife always liked Scotties Castle in Death Valley. Big Moorish looking mansion in the desert.

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#37

Should have....

Rob Lee

....stayed in Ottawa - going to 10C today....much warmer than Vegas!

Not often we get to point that out during the winter.... :b

Cheers -

Rob

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#38

the truth of why Derek is in Vegas...

Bill Tindall, E.Tn.

.....Miss America pageant. Told wife it was a wood working show, no doubt, and sent her shopping.

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#39

Here's a place to check if you want to feel warm *LINK*

Bruce, a MN Galoot

Ojmjakon, Siberia, Russia, the coldest continually inhabited town on earth. I check it whenever MN seems cold. On this past Christmas Eve, they hit -73F. Uffda! There is a video on YouTube showing a man stripping down to his swimsuit to take a plunge in one of the naturally occurring hot springs. The temp is -52F.


Ojmjakon

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#40

Ellis Walentine

Well then...

Ellis Walentine

... you need a proper picture of Norm, with the correct headwear....


Re: Shooting End Grain: How Heavy A Cut Do You Take?

#41

Groucho....you got quite a collection of...

roger lance

mugs in mug shots.

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#42

Re: Well then...

Phil

Its is amazing the direction some of these threads can take. We started out futzing with a dinky little shooting board, and ended in in Las Vegas, with Norm Abram!

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#43

Just out of curiosity,

Bruce, a MN Galoot

do you have a shot of James Krenov in a WC cap? :D

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#44

Re: Well then...

TomD

Well from futzing with a literal dinky shooting board, to futzing with a figurative dinky shooting board...

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#45

Re: Should have....

TomD

14C here in Toronto!

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#46

Re: the truth of why Derek is in Vegas...

Derek Cohen (in Perth, Australia)

The "Ms Teen America" is ample proof that there is a large percentage of the US population that suffer from overconfidence! :)

There are a large number of plump kids from what looks like 10 years of age upward walking around in swim suits, tiaras and capes, and chaperoned by an adoring mother, ignoring their goosebumps from the freezing cold weather. Perhaps US teens are tougher than we imagine? :)

Regards from Hell

Derek

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#47

Jack Guzman from Maine

Re: Here's a place to check if you want to feel wa

Jack Guzman from Maine

I noticed they've got a heat wave comin saturday and sunday. Brrrrrrr.---Jack

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#48

Impressions and some highlights of our trip so far

Derek Cohen (in Perth, Australia)

Is that it is easy to leave and go to Bryce or Grand Canyon or tour the dam/bridge. The "Bling" is to be experienced once I suppose. Derek are you visiting any place in the US we can be proud of showing off?

Hi Bill

Vegas is just a sensory overload. Not my thing. However ...

Lynndy and I caught a tour bus out to the Grand Canyon and then the Hoover Dam. We are going to have to do this again, with a plan next time, simply because there was so much more that we lacked time to see. The tour guide was good, and the bus was half-filled with Aussies. The bus stopped at a few vantage points, however it is so obvious that 99.9% was escaping us. What I did see filled me with awe and wonderment. I would love to do a ride through the Canyon, shoot the rapids (that has to be less difficult than snow skiing with Rob - who is a damn fine skier, by the way), and generally explore the natural beauty of the area (which is my thing). We did the Sky Walk, which was scary but amazing.

Video of the Sky Walk: http://m.youtube.com/#/watch?v=_LixP9oM75A&desktop_uri=%2Fwatch%3Fv%3D_LixP9oM75A

This is the Australian equivalent of the Grand Canyon (I have yet to visit, and am now highly motivated to do so): http://www.australiantraveller.com/alice-springs/australias-grand-canyon/


The Hoover Dam was a bit of a bust. Our bus was not permitted to stop on the bridge. Photos had to be taken as we drove by. The snippets we saw were spectacular.

I mentioned in a post about a week ago that I did not plan to write much about the trip, which has so far gone 3 and a bit weeks. It is a holiday, and personal. I will, however, mention the itinerary and also a few items of interest to woodworkers.

We travelled from Perth to Sydney (5 hours) and then to LA (15 hours), where we stayed over night before flying to San Francisco for three days. We walked the Golden Gate Bridge in the sunshine, ferried to Alcatraz in the pouring run (which seemed appropriate), rode the cable cars, great restaurants, shopping. A wonderful time.

Then four days in Sarasota, Florida for Christmas with very old and dear friends. Hired a car and drove around a lot. Of course, too late we discovered that David lives in China Beach, which was a short drive away. I think that he was trying to protect the locals from us. Next time David. For sure!

A week in Manhattan, including New Year. The last time we were there was 8 years ago, and it was warmer then. It snowed our first day, which was training for Ottawa.

There were two woodworking highlights of our stay. The first was a visit to Tools For Working Wood (this quietly ignores the adventure in finding our way there). I had a great afternoon playing with Joel's tools and seeing his set up while Lynndy escaped off on her own. There are photos of sawing dovetails and a tenon - trying out Joel's superb saws. I will upload these when I can. In the evening Lynndy and I joined Joel and his wife for a wonderful evening at their home. (... and I got to see Joel's personal collection of Norris planes, and a whole lot more. Oh boy!).

The second highlight was taking a train to Wilbur in New Jersey. We got there in time for lunch, then had a play (of course!) in his shop at home. This was the first time I had been in a basement workshop. Wilbur has a sweet shop, geared to Japanese tools. I got to hold (but was too scared to use) a new (!) Yataki ryoba. The stuff of legends.

It was so great to meet Joel and Wilbur. Both are terrific guys. Now I can write to a person, and not just a name/face.

After NYC, we landed in Ottawa for 10 days. Some of the time was spent in visiting the Lee Valley factories (I have briefly mentioned before how I was blown away by the size and professionalism of the company), finally meeting the design staff (with whom I have corresponded for so many years), sitting in on a couple of design meetings, was totally (!) gob smacked by the extensive tool library at Lee Valley (this has to be seen to be believed - some of the most rare and some of the most stunning tools imaginable), and spending lots of time with Rob and his wonderful wife (my first BBQ in the snow!) in and around Ottawa, and then a three-day visit to Mont Tremblant (where Rob proved he could ski and that I could not). The weather was the coldest we have experienced anywhere, but the snow was such fun. We had the best time.

So here we are in Vegas, due to return to Oz the day after tomorrow, via Sydney (spending a couple of days with my brother and his family).

Warm regards to all

Derek

Re: Shooting End Grain: How Heavy A Cut Do You Take?

#49

Ellis Walentine

Nah, this is the best I can do

Ellis Walentine


Re: Shooting End Grain: How Heavy A Cut Do You Take?

#50

Re: Nah, this is the best I can do

Bruce, a MN Galoot

I'd have given a LOT for a picture like that with me in it!