New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

"What Have You Been Working On?"

Posts

"What Have You Been Working On?"

#1

"What Have You Been Working On?"

Bill Tindall

It is the 1st of the month and time for the twice a month question.

It was a busy weekend for me, aided by visiting Son-in Law. We went through an air dried pile of lumber to pick out material for some way in the future drawers, as well as lumber for Son-in laws bench. We got the oak bench parts rough cut and now they are drying. Traveled to Knoxville with a friend to pick up a few hundred feet of free veneer from a retired woodworker. Fixed the roof to a sheep house, fixed stairs that go down river bank, and began preparing lumber for drawers for current project. Amongst this all, the kitchen sink faucet broke but I was able to fix it with a part made on the lathe. The inevitable leaks in related parts occurred (I hate plumbing). Washer failed and we got a new Speed Queen thanks to a suggestion on the main Forum, a model that enables me to thumb my nose at EPA washer regulations. This one uses both water and electricity according to my needs and desires. And finally we replaced the radio that failed in the car only to discover two bad speakers besides. No idea how to get to them. Hope to get at drawer making this week and use the new LV chisel.

Re: "What Have You Been Working On?"

#2

Molding for chest of drawers

Bill Tindall

I wish someone would write an article on making molding. These Chester County pieces have molding for which I have no router bit to cut.


What I have been brute force doing is to waste out the pattern with table saw and router and then scrape to get the final profile. The scraping goes almost as fast as planing once I learned to sharpen the scraper. It is essential to polish the scraper sides and that was the trick. I scraped 16' of top and base molding. All the molding is now done and I hope I don't screw up any installing it. Another secret to scraping is to choose the wood wisely. It needs to be straight grained and dense.

Re: "What Have You Been Working On?"

#3

Re: "What Have You Been Working On?"

rononkokomo

1) worked on grounding the Celtic R carving that I am doing as a lesson

2) put coats 2,3, and 4 of Maloof finish on arts and crafts side table

3) cut tenons for a different kind of arts and crafts side table.

4) did more research on new bench. Gonna modify my design by putting a 3 x 12 flush with the front legs and top put a bunch of holes in it as an alternative to sliding deadman.

5) worked on honing 2 hand axes. More to do. Also working on honing a Scorp. '

Did a bunch of cookin this weekend.

Re: "What Have You Been Working On?"

#4

Re: "What Have You Been Working On?"

Bruce McCrory

Over 30 years of financial records. Their only value now is nostalgic. Disposal is a problem. Right now, a metal fire 'pit' is serving double duty.

Oh, didn't you mean chores?

Re: "What Have You Been Working On?"

#6

PS, awesome loaves of french Bread

Bill Tindall


It finally, and probably accidently, all came together- taste, texture, shape.

Re: "What Have You Been Working On?"

#7

I am challenged

rononkokomo

I can't get my IPad to post them

Re: "What Have You Been Working On?"

#8

Re: "What Have You Been Working On?"

Bob Hackett

Spent an excellent 3 days with my youngest son dragging out older seldom used tools and modifying them to fit his needs and then my older brother (who was up here visiting from Utah) and I sent him back down to RI with a carload of new potentials. Some of those old tools were handmade and used to belong to his grandfathers. THAT was one of the high points of the year for me.

I`m also working on finishing a shave horse that my brother Bill and I started designing/building using whatever I have on hand. It`s turning out better than expected and with a little help from more digitally oriented minds I will attempt post pics when it`s finished, hopefully in a few more days.

I mailed off a bronze bladed boline with curly maple handle to an excited customer. If I get the pic posting thing down I`ll post some of that as well. Those on Facebook can see some of the other things I`ve been up to including a greenhouse I built for LOML by going to her Ancient Star Herbals page.

Re: "What Have You Been Working On?"

#9

Re: PS, awesome loaves of french Bread

TomD

Was there a recipe thread? I probably posted on it....

Re: "What Have You Been Working On?"

#10

Re: "What Have You Been Working On?"

Stuart Hough

Aside from working the J.O.B., I started flattening my workbench top. Traversed at a 45 degree angle with the jack skewed to knock down the hump in the middle. Then I took out the #7 and did some more angled traversing. I worked on it for about 2 1/2 hours. Now have it almost flat in all directions. I think one more session with the jointer plane, and then on to the 4 1/2 smoother. I will then only need to mount the vises and drill the dog holes and will finally be finished. Pics will follow soon.

Re: "What Have You Been Working On?"

#11

Re: I'm making a 1/2 scale version

George Allchin in Lowell, Mich.

of our home town theater marque. pictures to follow. None now it is just a frame, it's hard to see in my cluttered barn.

Work safe,

George

Re: "What Have You Been Working On?"

#12

you can't post them from your iPad

Bruce, a MN Galoot

and neither can I. OTOH, I don't know anyone who can.

Try posting them on a mass storage site like flickr or photobucket and then load the link. Or use your regular computer and post away.

We need the pics!

Re: "What Have You Been Working On?"

#14

Re: Molding for chest of drawers *LINK*

William Duffield

Don McConnell of Old Street Tools (formerly Clark and Williams) has made two videos on making mouldings, using traditional wooden moulding planes. They are produced by Lie-Nielsen, and can be purchased from either L-N or directly from planemaker.com.

Matt Bickford is currently making another video on the same subject, also produced by L-N. Matt's web blog, Musings from Big Pink, explains the process in detail in over a hundred installments and innumerable photos and drawings, as does his book, Mouldings in Practice, recently published by Lost Art Press. All these sources rely on the use of a half set of hollows and rounds, rabbet planes, a pair of snipes bill planes, and a pair of side round planes. The snipes bills and side rounds are only required for the less commonly found patterns. You can easily substitute a dado stack in your table saw for the rabbet planes. The dado stack might actually save you some time on a long run, but maybe not on the molding for one chest.

Why "Big Pink"? That is the name he has given his antique beech workbench where he builds his moulding planes, that still shows peeling pink paint on several surfaces.


Musings from Big Pink

Re: "What Have You Been Working On?"

#15

Re: "What Have You Been Working On?"

Derek Cohen (in Perth, Australia)

This past weekend I was building parts for clocks. Nothing exciting or fancy, just sections in MDF for a clock I designed to be used when training impulse control and organisational skills in ADHD and Autistic children. It is something I came up with nearly 20 years ago, and has been used with excellent results in schools and home settings. In October I am presenting a workshop at our national conference on clinical psychology on the research I have been doing over the past 20 years with ADHD children. This is among a number of visual aids I will need. It may not have been fine woodworking, but I enjoyed refining the design and seeing these pieces come together.

The previous weekend I spend some time building a closed plane handle while testing the curve for pre-production Liogier handlemaker rasps.

It seemed reasonable to add a body to the completed handle (what else would you do with it?). I found a 2 1/4" wide and tapered 3/16" thick Sorby blade that seemed a good size. I decided on 28" for the length. Why 28"? This is a manageable size in a longer jointer. I have a 30" which feels just a little too long, and also too light (the body is low in the tradition of the HNT Gordon planes). The 28" ended up weighing about twice as much as the 30" even though it is another razee design. The bed is 55 degrees to deal with interlocked grain.

This wasn't such a big deal since the body sections were already lying on my shelf, rejects from the time I built a laminated cooper's jointer. In retrospect there was a downside to this - the sides were dimensioned for a lever cap, and I chose to add a wedge. Consequently, the design was an attempt to deal with this limitation. Tell me what you think.

A few pics ..



How big is it?

Well, it seems small against the 36 1/2" coopers jointer (rear) and a bit larger than the 15" jack (front) ...


In use it is balanced and comfortable, even on a 1/2" edge ...


Regards from Perth

Derek

Re: "What Have You Been Working On?"

#16

The impracticality of the suggestion

Bill Tindall

While it can be of historical interest to know about making moldings with molding planes it is not practical in a modern shop focused on making stuff rather than making stuff Period correct. Consider the barriers between starting at zero and successfully making 8' of custom molding entirely with hand tools And then not needing to make another 8' for a year or two.

I have tried equipping the shop with old tools and that is similarly impractical. I ordered a couple of rounds from what I was told was a reputable dealer. It took hours to make them functional. I had the same experience with chisels and similarly wound up with a partial, and hence useless, partial set of chisels. I can make a new chisel much quicker than removing the pits from an old one.

I could buy a used shaper and special order a cutter for the price of a new set of hollows and rounds, and not have to wait a year to make the molding. That is just one of several routes to short runs of machine made molding I saw at IWF. But here too, these options are impractical for making 8' today and 8' next year.

People have figured out how to make 8' of cove using a table saw and scraper. Probably someone has figured out a practical way to make other useful profiles using a combination of power tools and hand tools. That is the article waiting to be written.

A router mounted on some sort of arrangement that would enable a round nosed bit to engage the stick of wood at other than 90 degrees would be grand. Such an arrangement would enable a profile to be roughed out much like people are doing with CNC routers for short runs of molding.

Re: "What Have You Been Working On?"

#17

suggestion/question

Bill Tindall

Should this technique be posted on all the WC Forums, maybe by Ellis, as a new topic with a title that indicates what lies within for those that need the information?

A superficial statistical analysis reveals that a post is much more likely to be viewed if it is flagged that it contains a picture. Hence, it is to everyone interest that people know how to attach pictures.

Re: "What Have You Been Working On?"

#19

Re: The impracticality of the suggestion

Warren in Lancaster, PA

I have made thousands of custom mouldings with hollow and round planes. Some times only a few feet or a few inches are needed. There is no faster or cheaper way. It costs more to make a cutter and set up a machine than to make moulding by hand.

The length of moulding dictates the method. For a thousand feet it is worthwhile making cutters and setting up a moulding machine, but that first foot costs an awful lot.

Re: "What Have You Been Working On?"

#20

Here's a pic 


img

Re: "What Have You Been Working On?"

#21

Be gentle

rononkokomo

My second attempt at carving with a lot of work remaining to be done.

I do want to incorporate some carving in furniture projects soon.

Ron

Re: "What Have You Been Working On?"

#22

Re: suggestion/question

rononkokomo

Photo bucket for IPad. You just have to remember to delete the pre printed http// on the wood central page

Re: "What Have You Been Working On?"

#23

Re: Be gentle

Bruce McCrory

Looks good to me! Is that poplar?

Re: "What Have You Been Working On?"

#24

Ellis Walentine

Not an iPad user, but

Ellis walentine

I did download Picup app from the Apple app store, and it seems to work fine, although I don't really know how to cut and paste on an iPad, so this was a little bit clumsy.

Ellis


Re: "What Have You Been Working On?"

#25

Re: Be gentle

rononkokomo

Yes poplar