Re: Very Rich
William Duffield
Rob Lee hinted that they are working on tapered blades of PM-V11 for molding planes.
Knowledge You Can Build On — Est. 1998
Re: Very Rich
William Duffield
Rob Lee hinted that they are working on tapered blades of PM-V11 for molding planes.
Re: Very Rich
david weaver
They show up here (the planes) but fairly rare that they're in matched pairs or even in a similar pitch and size enough so that they could be sized together
If you can come up with the materials and tools to build them, it just takes a lot of screwing around out of the equation. Making irons with 1/8" O1 stock is no harder than dealing with an old iron that doesn't fit a plane that has to be reconditioned.
If I decide I've made enough and will buy planes in the future, I think I could sell my floats and other tools without much loss because they have the silver bow on them that is the LN brand name.
Re: Very Rich
david weaver
Like hollows and rounds? I don't know, I size those to the plane in question with a file and then a stone and then harden and temper them.
I'd hate to have to work with them in hardened state if they weren't dead on the size of the plane already.
O1 is a blessing to work with and a blessing to sharpen. it doesn't warp much, you can harden it in an open atmosphere and get good results, and you can temper it in a kitchen oven. I'd be extremely reluctant to do anything other than buy 1/8" O1 bar stock, which is pretty cheap, and use plain old soybean oil to quench it. I haven't yet had an iron turn out bad, and it files nicely when annealed and is so easy to work.
Re: A simple outdoor table in English oak
Sgian Dubh
William, the legs are tapered only on the inside narrow edge. The wide faces, those that are parallel with the long side of the table are not tapered, which is also the case with the outer narrow edges of the legs.
The finish applied is simply one coat of boiled linseed oil. Its ability to delay the greying effect due to exposure to the elements is therefore minimal, as is its ability to protect the wood from rain, water vapour, and spillages of wine, beer, coffee, mayonnaise, or scuffs from knives, forks, the bottom of rough ceramic items, and so on is almost non-existent. The oil was applied for no other reason than to make the oak look attractively honeyed for the purpose of portfolio images, and I expect most of the parts to develop significant greying within about twelve months. No-one will ever again go anywhere near that table with any kind of protective finish as far as I know, and it will age and start to show real signs of decay within about 20 or 25 years. I like that kind of maintenance free durability, which saves a lot of time and wasted effort piddling around trying to refinish an item every year or two to stop it rotting away. Slainte.
Re: top question
Sgian Dubh
Bill, the joinery for the top is quite conventional really. The top is just under 5' long by 30-1/2" wide, adequate for six people eating informally. The long rails are are about 3-1/2" wide by ~1-3/8" thick. The three short rails (two ends and a middle rail) are roughly 4-3/8" wide by 1-3/8" thick. The 14 slats are ~2-5/8" wide by a hair over 3/42 thick, and spaced about 3/8" apart.
The four corners are joined with draw-bored M&Ts incorporating a sloping (secret)haunch facing towards the outer corner. The purpose of this haunch is to reduce the chance of the two pieces of wood drifting out of alignment on the wide faces as the wood tries to cup due to seasonal changes in moisture content. The draw-boring is effected from the underside of the frame and the dowel pegs don't penetrate all the way through to the top. This is so that there isn't dowel end grain on the top surface which would act as a wick drawing moisture into the joint leading to accelerated decay. The glue used was polyurethane, which I'm not a great fan of, but it's a good choice for exterior joinery because it's really one of the few glues suited to wood and its joinery that's likely to get wetter than 20% MC. Also, the mortices are about 3/16" longer than the width of the tenon, so the wood has room to expand as it takes on moisture, and draw-boring the joint means that even if the glue fails the joint should remain relatively structurally sound for many years.
The middle rail is similarly M&Td and draw-bored in place but there is no haunch, just shoulders of about 3/8" on the narrow edges of the rail, and a similar shoulder on each wide face. Incidentally, all these mortices and tenons are 3/8" thick (tenons) or wide (mortices). The purpose of the middle rail is to lock the long rails in place to prevent its outward edge bend, and it is also where a hole is bored to take the pole from an umbrella-- nice and stout for that purpose.
The slats use a 5/16" thick tenon penetrating roughly 7/8" deep into individual mortices worked on the inner edges of the long table top rails. The tenons are about 1-3/4" wide and the matching mortice is a shy 1-7/8" long, give or take a 1/32". They are dry fitted together because there's no need to glue them in place because the outer frame and centre rail provide all the strength required. Assembly of the slats is facilitated by heavily chamfering a tenon on one end of each slat. During the glue up of the whole lot in one go you slip the unchamfered tenon of the slat into its mortice meaning you can line up the other chamfered ends to their mortices very easily-- once the chamfer has partially engaged with the mortice whacking the frame together means the whole lot guide themselves into place really.
And once the draw-bored dowels are banged into their appropriate holes you can take the clamps off if you want. Slainte.
clever design features...thanks
Re: Very Rich
William Duffield
I was wondering how one might go about shaping a PM-V11 bade blank. The only PM steel I have any experience grinding is CPM-V3, which is a high speed steel, so I had no concern with ruining the hardness. It is tough. It was a Crown PRO-PM bowl gouge. I thought I'd save 20 clams or so by buying the fingernail grind and reshape it to an Elsworth grind. It took a lot longer than I expected to reshape it on a slow speed grinder, so I'm not so sure it was a good deal. But, that's not the point.
The point is: How hot can you get the new Veritas PM steel without taking the hardness out of it? I can't find any data on the Lee-Valley websites that states whether or not it is a HSS. And when Rob Lee hinted at blades for molding planes, I don't think he mentioned whether they might include blanks for end user shaping. Perhaps he was only thinking about blades for the Veritas plow and rabbet planes. I don't figure that it would be amenable to reheat treating in anything less than an industrial setting.
Re: Very Rich
TomD
That issue was covered in some earlier posts by Rob. Could have been the tapered blade question thread were he first mentioned they were working on it, which might help with the search. I don't know if the exact transformation temp was revealed, but he did state it was not an HSS. So one will have to display some circumspection in grinding the stuff.
Re: Very Rich
TomD
Yeah, O1 is great, though we both have the upside of already owning the torches that make heat treating them easy.
I would actually be leery about buying second hand floats, at least sight unseen. Or maybe I am just imagining that others would feel that way. I think people may want to pass them on when they get dull, and not want to sharpen them, or sharpen then and end up doing a bad job of it. When making my own, I noticed that the saw edged ones were not only a lot less work to make, but that at the widest, there was a tendency for the file to skate and round the edges of the float. This was despite every effort to actually use the file belly to hollow the tooth, but the wider section of the tapered flat face float were hard to control. So I think sharpening hardened ones could even be harder to do.
molding for interior trim
Darrell in Oakville
I've been working on about 75 feet of trim for our cottage. It's white pine, ground down to about 5/8 thick by a lunch-box thickness planer. I took a few of swipes with a smoothing plane to the faces and edges to clean them up.
Back side is relieved using a plow plane with a 3/4 inch cutter, overlapping cuts from each side. It was set very rank, so 3 passes on each side was plenty.
The profile is made using a triple reed plane I rehabbed. I used a chunk of pine with a rebate cut in it as a fence for the molding plane. I had the plane set fairly coarse, as these old ones tend to choke on fine shavings. Thicker shavings are ejected better. But you gotta make sure the iron is sharp to get a good finish on the profile when making heavy cuts.
Bevels on the edges are roughed out with a small chamfer shave set really coarse. Finished off with a smooth plane, with a wooden fence clamped on to limit the width of the chamfer.
The floor is a mess, but the moldings turned out quite nice.
messy floors
Jack Guzman from Maine
are a sign of productivity. Nice looking trim. ---Jack
What Lee Valley said
Bill Tindall
....the new stuff has a final heat treat similar to A2. I haven't looked up A2 but it is about 350 degrees F.
Re: Very Rich
david weaver
In the steriod pumped world of sharpening we have, I don't let any get dull, but your point is a good one, someone would have to be assured that they were in good shape, and if I sell mine, I'll touch them up and take a picture of the tooth line with a straight edge sitting on top of it (not that the teeth on a float have to be absolutely perfect for it to work well, but things being beyond where they actually need to be to do good work still makes it easier to sell stuff...ask the japanese, Lee Valley and Lie nielsen, right?).
The mouldings are such a small part of any project I do, but in terms of design, but little in terms of the use of a hollow or round, that I think it's fair to say that I have all I'll ever need in my shop to make super functioning moulding planes.
How many woodworkers don't have a mapp torch for some reason or another? I can just (with two firebricks from an amish store) do an iron that's about 1.25" wide, with one, and about 2 inches wide with two of them, though anything that big I usually use a weed torch. Not super precise, and pretty uncomfortable to use one (a lot of excess heat), but it works pretty well.
We are in an era of a lot of things that get bought and never used, though, so no matter what is sold, if it looks good on a catalog page, or if it gets a positive review in a blog, it will probably sell well.
I would presume that LV being LV, if they offer tapered irons, they will have some handouts about how they expect users to fit them to planes or with suggestions, etc.
Re: What Lee Valley said
TomD
A2s tempers at 400-1000F. According to crucible.
Lots of stuff...
John in NM
First off, we have a bunch of gunstocks that are mostly commissioned work. Walnut, maple, and a cocobolo grip. I use both power tools and hand tools to make these.
Also built the two lower cabinets for the guest room kitchen, I'll only bother to upload the interesting one, such as it is. Sink base, going to have 4 doors of various sizes, and 6 x 6 tile in the horizontal rectangle (sink will be behind that):
Today we did some of the finish plastering in the guest house. Three coats of plaster over chicken wired straw bales:

Last week I made some much needed shelving over the windows in my very much incomplete workshop space. As you can all see, a whole bunch more work to do in there:
Also added a new router and lift to my temporary (going on 5 years now
) router table. So glad not to have to fight the plunge router screwed to plywood anymore that I'll even post a picture here on the handtools side 
