New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Is anybody making anything?

Posts

Re: Is anybody making anything?

#51

Images from an iPad

Derek Cohen (in Perth, Australia)

The iPad is certainly no substitute for my MacBook Pro. However it is significantly lighter, and it is easier to cart around on a plane. To post with pictures one must access a site such as Photobucket.

For the past few months I have been discussing a parallel guide adjuster designed by Jim Ritter. My input has largely been devil's advocate while Jim sharpened up the design for production.

The leg vise parallel guide adjuster is an alternative to the St Peter's Cross, both of which enable a leg vise to function without the pin adjuster. No more stooping and setting the parallel guide for a specific width. Instead there is a single setting for all work pieces. Here are a few images ...

The chain drive:


The chop clamps securely at all distances - note the absence of the traditional parallel guide adjuster:


It is not easy from an iPad.

Regards currently from a wintery Cape Town

Derek

Re: Is anybody making anything?

#52

Re: Images from an iPad

William Duffield

I see that PhotoBucket says that they have an app for iPhone/iPad, but I am skeptical of their offer of a "free" service (TANSTAAFL), since it seems that I must sign up before I can even read details of how it works. Worse, it was once owned by Rupert Murdoch (guilt by association)! They also use the time-based bait-and-switch model, where it is virtually assured that some time in the future, the service you have used and grown to rely upon will require you to pay a fee to continue to use it and, worse, to continue to have access to and control of your personal content. I can't even redownload the images I upload to them without paying a fee. No thanks--that's not free, unless you use Janice Joplin's definition.

Re: Is anybody making anything?

#53

Re: Is anybody making anything?

Sgian Dubh

Thanks for the response Derek.

I've seen the desk and table before. I like the appearance of both, but I question how stable the chair is likely to be in use. My experience is that chairs with just three points of contact at ground level aren't stable and are a bit of a challenge to use. Whilst it's true that a three legged item will always find three points of contact on the ground and therefore 'self levelling', unlike a four point of contact item in many cases, dining chair seat height items compound the instability if there are only three legs. It's all about leverage I suppose, and whilst acceptable in a low stool such as the classic milking stool used on rough and uneven floors, the instability tends to get a bit irritating in taller pieces. Slainte.

Re: Is anybody making anything?

#54

Re: Is anybody making anything?

Derek Cohen (in Perth, Australia)

Hi Richard

I agree with you on all points. While I have the utmost respect for the design and work of David Haig (who is shortly to run a couple of workshops here in Perth), The idea of a three-legged chair is not one I find reassuring, despite the familiarity of Antipodeans seeing the world from unusual vantage points! :) I plan to build a desk inspired by David's desk, but the chair for the desk is inspired by Sam Maloof ( who kept all fours on the ground).

Still in wintery Cape Town, where the sun is shining.

Derek

Re: Is anybody making anything?

#55

Re: Nope. I'm traveling in Vietnam.

roger lance

Kees....when you get back, how about an update ??.....I'm sure theres a few vets that would be interested in hearing about your journey....I know I am.

Re: Is anybody making anything?

#56

Re: Nope. I'm traveling in Vietnam. 

roger lance

Kees....I just got back from visiting the traveling Vietnam Wall which was in my home town this week....my first time seeing the Wall....on my way out, I stopped and bought a hat....my first piece of paraphernalia in 40 years....placed it with some planes....this is woodworking afterall....


Re: Is anybody making anything?

#57

Re: Is anybody making anything?

roger lance

I was a LOT younger and stronger when I put these in the landscape 35 years ago....can't wait to return to that nice clean, cool woodshop and leave this yard work behind !!


Re: Is anybody making anything?

#58

Ugh....

John in NM

You deserve a very cold beer :D

UP re-did the tracks around here a few years ago, for a while the town was lousy with old ties. I used a bunch for fence corners, since my runs are short I didn't need to build a proper corner. I mostly picked out the oak ones, which turned out to be a dumb mistake - man is it hard to pound fence staples into them!

Re: Is anybody making anything?

#59

Re: Ugh....

Bruce, a MN Galoot

'bout 16 years ago I helped the rangers of T. Roosevelt Nat Park in North Dakota build an enclosure to load buffalo. It was made of bridge planks fastened to railroad ties with ring-shank pole barn spikes. My arm was pretty well shot after that day.

Re: Is anybody making anything?

#60

There are times when power tools are kinda nice...

Bill Houghton, Sebastopol, CA

Pole barn screws and an impact driver would be far more fun for a project like that.

Re: Is anybody making anything?

#61

Re: Is anybody making anything?

CStanford

Chair in dry fit --- the last chair in a set of six Shaker low back dining chairs. I haven't made post and rung chairs in quite a while and I really started having fun with it again at about the third chair. Once glued, there will be some final shaping and tweaking of the slats and back posts and then off for weaving. My wife is taking a crack at weaving the prototype (I always build one extra chair on a job like this) which will be for our daughter.

http://i1051.photobucket.com/albums/s427/CharlesStanford/ShakerLowBackDryFit.jpg

Re: Is anybody making anything?

#62

Now THAT is an excellent idea....

roger lance

and theres some Sam Adams Boston Lagers in the fridge !!

Re: Is anybody making anything?

#64

Re: Looking good Charles ...

CStanford

How about the most beautiful part of all - a scan of the customer's check! I'll redact the account number and name!

Re: Is anybody making anything?

#66

Re: In my house...

david weaver

...if the check was made out to my wife, I'd call that "express" or "direct deposit".

Why make extra stops before it gets there? :b

(sort of kidding, my wife does do the shopping for all of the staples, but is very good with money).

Re: Is anybody making anything?

#67

Re: Looking good Charles ...

CStanford

Straight woodworking-by-recipe. I did the first chair to original dimensions and the client wanted 'em a little chunkier. I added an eighth inch in diameter to the posts and made the slats 3/8" thick. They loved them. These are destined for a lake house I'm told.

Re: Is anybody making anything?

#68

That is why...

John in NM

I cash them :D