Most table saws have cast iron tables.
Pam Niedermayer - Austin, TX
Knowledge You Can Build On — Est. 1998
Most table saws have cast iron tables.
Pam Niedermayer - Austin, TX
In some areas
Bill Houghton, Sebastopol, CA
my area being roughly in the middle of the pack, I think, it's possible with a little looking to find table saw corpses - old Craftsman saws that aren't worth restoring - for right cheap or even free. Other stuff, too. When we cleaned out my dad's garage, one of the pieces of equipment that had followed him home from the gas station (Texaco, 1963 or so to 1966 - I wore the uniform shirt for years before it finally wore out) was a device to test that connecting rods are straight, consisting of a big flat surface against which the rod was held. This followed me home, too; my intent has been to cut it up for the big flat surface, so I can try Bill Tindall's* diamond sharpening regimen.
Granted, not everyone has a dad who owned a gas station with now-obsolete equipment of quite that obscurity; but it's hard for me to imagine that there's not flat cast iron scrap not too far from most folks. For instance, automotive disk brakes use cast iron rotors that can be turned down only so thin. A brake shop might well be able to unearth a large rotor that's gotten too thin and turn it smooth for you (they've got special lathes that get the job done quickly and thus cheaply). This might make for a short-stroke cutting regimen - you'd have to try it to see how much clear surface you can work on, depending on the size of the rotor - but most everywhere's got brake shops.
You might post a "wanted" on your local Craigslist for worn-out tablesaws.
Lots of possibilities out there.
*Not that Bill Tindall invented it; but I was inspired by his research into efficient diamond sharpening, and the regimen he suggested is in my pile of "things I printed out to implement when the round tuit supply is good."
Re: In some areas
Pam Niedermayer - Austin, TX
Yes, the only real trick is convincing a proud owner that his/her table saw is actually worn out. 
Pam
Re: Making Lapping Plates
Tom Colligan
OK, fellas. Now how often do you apply new paste to your cast plates? If a week goes by w/o sharpening do you automatically put another dollup on the plate?
Would there be anyting unsound about using a small corner of a lathe bed, jointer table or TS, marked and dedicated to its own grit of paste? Thank you again. Tom
Depends
Bill Houghton, Sebastopol, CA
There was a free one around the corner from us last year - put out on the front sidewalk. I'm not sure how many minutes it was there, but it wasn't more than five minutes after I saw it before it was cleaned up. Working motor, too.
Re: In some areas
anotherBob
I haven't asked yet, but... assume that most here that use a cast iron substrate sharpen free hand, yes?. If sharpening/honing/stropping with different grits, and using a jig... you would have to have one for each grit to avoid cross contamination, right.
So, I received my 6" x 1" rounds and delivered them to the grinder... going to be next week some time till they're back home. Did a little research last weekend and ran across something that a lot of the knife makers use: http://www.edgeproinc.com/ With one of these, and a much smaller, say, 1/4" thick by 2" x 6-8" piece of cast iron for the diamond paste, might be easier to come across. Wouldn't be too tough to cobble together something like the EdgePro if you had the inclination... or just get the thing outright. Curious if anyone here has seen or used that rascal. There are a bunch of videos on youtube about it and pics of spit hair after using it on knives... plane irons and chisels ought to be a lot easier to hone (just one side vs both sides for a knife, unless you want a back bevel... but looks like that would be pretty easy to accurately do too...)
Re: Making Lapping Plates *LINK*
David Barnett
"OK, fellas. Now how often do you apply new paste to your cast plates? If a week goes by w/o sharpening do you automatically put another dollup on the plate?"
When a plate is new, I hit it with dots from the syringe evenly spaced about 3/4" to 1" apart, rub in circles to get even coverage, then press it in with a half-boule of synthetic sapphire or ruby (I love these. So cheap and so useful -- not just for this). You can also use boron nitride or roll it in with a hardened steel bearing or something along those lines. Failing this, just start flattening a blade. Keep recycling the swarfy compound left on the blade and do this until you feel like something's really happened. If it gums up, gets sticky or dry, spritz it with WD40 or spread a few drops of olive oil and make some more swarf.
At some point, add about half as many dots as the first go and have at it again. Subsequent chargings will likely demand less compound. Remember, the tendency is to add too much rather that to underdo things.
After a lap is broken in, I really don't charge it that often. A few dots are enough from time to time. When you get it, you'll add a bit of paste or lube it to make things work more smoothly. To be honest, I'm sure I use more than is needed, but as cheap as it is, I really don't care.
You can let it dry up on the lap and refresh or extend it, (diamond lube is often marketed as extender) with a drop of lube to get things going again.
You'll know when you need more diamond.
"Would there be anyting unsound about using a small corner of a lathe bed, jointer table or TS, marked and dedicated to its own grit of paste?"
As for repurposing iron machine beds, and is it unsound? Well, I wouldn't want diamond grit to end up abrading jointer knives, so it'd be a matter of cleaning up with WD40 or mineral spirits. Would I do it? Probably not, but then I have dedicated laps. If you're doing only 14000 grit, though, you'd probably get away with it. I do like your thinking, at any rate.
There are many suitable and cheap gray cast iron surfaces that are ground flat enough for lapping...
Try the cheapest angle plates from Enco (gray iron angle plates). They're square rather than rectangular, and thicker than you'd need, but hey, they're yet another possible lapping surface, and as I said, they're cheap, especially if you cut one in half, or better, quarters. Smaller is less $$$. Bigger is nicer. For a little more, you can get the universal right angle irons. They're rectangular and the center web allows them to sit on a benchtop.
Enco gray cast iron angle plates
Re: Making Lapping Plates
TomD
I wouldn't want to do that, I don't want to contaminate my tools with diamond particles. And how would I keep the grease clean or off my wood. There are lots of sources of cast iron around, not maybe easy to find in a few seconds, but not too bad to find in a few months if you are patient. I just keep adding them, and keep my eye's open.
I don't refresh with paste, I add lubricant. the stuff has dried up not fallen off. I keep at it until I feel the cutting diminish.
Re: Stop Searching!
craigd
This has been a most excellent thread.
I got 36# of cast iron for $15 at the scrap yard and with just a bit of machining & lapping (uh, yeah, add about $1000 for my labor) I got a couple of 12" x 5" plates.
The exception proves the rule?
Pam Niedermayer - Austin, TX
Honing guides and/or freehanding *LINK*
David Barnett
"Wouldn't be too tough to cobble together something like the EdgePro if you had the inclination... or just get the thing outright. Curious if anyone here has seen or used that rascal."
The EdgePro is superb but far more suited to knives, scissors, and so on, than woodworking tools, and the Professional Model at $400 is very expensive, indeed. The Apex Model is far cheaper but still very useful and well-made. Again, however, both are better configured for knives than planes and chisels. Sure beats the Lansky, DMT Deluxe Aligner or the bulldog clip for quality and precision, but I'd have to use it a lot to justify it. BTW, I have only seen but not used either. Further BTW, I actually like the Lansky but haven't used one in ages.
As for making your own jig, by all means. Many have and it's loads of fun if you're so equipped and inclined.
"I haven't asked yet, but... assume that most here that use a cast iron substrate sharpen free hand, yes?."
I do, but I also use a jig at times depending on the tool and the task.
"If sharpening/honing/stropping with different grits, and using a jig... you would have to have one for each grit to avoid cross contamination, right."
Answer 1: Or use an intervening sheet of paper (or some other film) or a glide of some type under the guide's roller, which is what I use.
Answer 2: Not if you use this type of jig and shim your laps to consistent height (street price about $10 less, but easy to knock off with improvements).
Outrigger style honing guide
Excellent! And pretty, too.
David Barnett
Those look really nice. And 36# of iron should make a few laps. What machining went into these and did you do your final lapping by hand? Do you know what that iron was from?
Re: Excellent! And pretty, too.
craigd
Thanks! For machining, I cut out a piece (with a hacksaw, easy), put it on the mill table, shimmed it so I could clamp it without distorting it (which takes some time) and put stops around the edges to keep it from sliding (it is amazing to me how much an end mill can push things around) and took a skim cut. This gave a a flat bottom with just a bit of lapping (PSA on a bandsaw table (no surface grinder), checked on a granite surface plate). Then I can clamp without shims and hog off the dimples on the top (3/32", I'm using a 3/4" endmill with carbide inserts). I machined around the clamped areas and cut those off afterwards so I wouldn't have to reclamp (less chance of a screw up). Invariably, the center would be a little high so there was a fair bit of lapping to get that down. I stopped when I couldn't put a 0.0015 feeler gauge under any part, while pressing down on any other part.
I don't know where the grainaries source them, I think they are for sorting seeds (this is grass seed country (Willamette Valley OR) and those pockets are actually scoops (on both sides) that would hold a seed or three) and the yard guy said they are brittle and break easy, so probably not ductile. But definitely cast iron and did I ever have the black hands to show for it.
Re: Excellent! And pretty, too.
TomD
That edge pro thing sorta looks defeatist. I won't ever be an edge pro seems more apt.