Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Help with ideas

Posts

Re: Help with ideas

#51

Interesting idea--and thought on RJ's magnets

Wiley Horne--So. Calif.

Hi Marv,

That's very helpful--I hadn't thought about access from outside like that. After considerable mulling over, I'm beginning to see the wisdom of RJ Whelan's magnet solution. The magnets could be a permanent solution, or they could be used initially to get a feel for how the tray is going to respond to different levels of force applied in different places.

So I am ordering a sampler set of magnets from LV:

http://www.leevalley.com/wood/page.aspx?c=2&p=59362&cat=1,42363,42348&ap=1

Will play with these to see how small a magnet will get the job done. For example, those 1/8" rod magnets could be made invisible in the bottom of the tray--but will they work?? I'll find out.

Relative to your idea, it might be that using magnets arranged with like poles facing (so they repel) could be the minimally invasive way to get the tray to 'eject', and then it's just a matter of doing the catch/release, along the lines of your most recent and earlier suggestions.

Miuch thanks!! I'll report back on what I find out.

Wiley

Re: Help with ideas

#52

In the short time...

John in NM

That I spent working in furniture shops, about 3 years total, it always irked me to start on a piece without having the hardware in hand. In this case it wasn't for design reasons, as usually the design was settled and we were just building yet another one. Usually it meant I was going to have to stop and find something else to work on for a couple days once I could go no further without the hardware. :D

Re: Help with ideas

#53

Magnets

R.J. Whelan

Wiley,

I use the 1/4" rods for LV - they are remarkably strong .. rj

Re: Help with ideas

#54

Stephen Shepherd

I am not sure...

Stephen Shepherd

about the new rare earth magnets but all other magnets will eventually loose their magnetism, so make allowances for replacement in the future.

Stephen

Re: Help with ideas

#55

Re: Interesting idea--and thought on RJ's magnets

Marv

Wiley,

As you may know, I preach magnets and John Deere Green from time to time for certain applications.

I'm not sure magnets would be the best method here. A simple compression spring to push the drawer open seems to be very simple compared to finding just the right magnets.

A leaf spring would work too and you could make it to a size and shape to fit into a small space at the backend of the drawer.

It's kind of fun to have a hiden release button like that to surprise someone as you make the drawer suddenly pop out without them seeing you do it.

Marv

Re: Help with ideas

#56

Re: Interesting idea--RJ's magnets and Sgian Dubh

Wiley Horne--So. Calif.

Hi Marv,

This is one of those brain-teaser problems. Sgian Dubh's admonition is coming all-too-true, as I sift through the reality of the options....

Here is the back of the case:


The back is tapered around the periphery to an 1/8" tongue, which fits into grooves in the sides, bottom, and top. The back is just shy of 1/4" thick, and its front face is located 1/4" in from the back edge--I was trying to make max. use of a shallow cabinet, so didn't want to tie up footprint with a thick back.

The tray fits flush up against the back--again, I am trying to get max. use of available footprint--and the back of the tray is 3/16" thick.

So thinking about anchoring either a wooden spring, a metal leaf spring, or a coil spring--that's how much meat there is to work with. 3/16" usable in the case back, and 1/8 usable in the tray back. When the tray is inserted, the spring has to be flush into its 'hole', so we are talking about a short spring, and if it is a leaf spring, it has to be strong enough to push the tray but thin enough to collapse into a very shallow hole or slot. Oh, and the shelf above the tray is 1/4" thick.

That's why I'm trying to figure out how to use the side or bottom for anchoring anything, because there is plenty of thickness there.

Am also trying to do something that is minimally invasive or disfiguring, which is why I put Dan Donaldson's idea of the two-way open/close mechanisms on hold for a while--would have to chisel a pretty good size slot in the tray bottom for it to work.

The above reasoning is how I arrive back at RJ's idea, because magnets don't take up much room. Stephen is right though--they aren't forever.

Maybe I'm finding out why Mr. Krenov didn't use a tray in the bottom of his design; probably not because he didn't think of it. The most Krenovian thing to do is carve a finger hole right into the tray front--but it has to be a really artistic and organic looking finger hole. I ain't got the guts to do it. Yet.

Wiley

Re: Help with ideas

#57

Re: Help with ideas

Joanne in Point Pleasant, PA

Ah, that makes sense. When I first saw the interior, I thought about hanging pendants. It would be a shame to cover that beautiful wood, but the ultrasuede or cloth idea sounds perfect. I lined the drawers of a jewelry cabinet I made my sister with ultrasuede (and foam underneath for cushioning). It's nice to protect the wood and the jewelry.

Good luck with matters at the UN. The world has some great troubles. :-)

Re: Help with ideas

#58

Alternative Krenovian

Bob Hackett

Since you`re going to line the case with some kind of cloth why not put the hole in the case bottom instead of the drawer front?

You could make the backing for the cloth in 2 pieces and have the smaller front section hinge up so you could lift a small part for access to the finger hole.Stick finger thru hole and push on back of drawer front to open drawer.

With the cloth lining down the hole would be hidden.

MB

Re: Help with ideas

#59

Nother idea....really simple

Marv

Hi Wiley,

Looks like you have a fairly thick front on the drawer. How bout if you drill a hole down into the top of the front right in the middle where the V is. Insert a long round or square magnet into the hole.

Just like having a key to open and lock the door, you could have a steel device or something made of steel that is kept on display on the shelf. When you want to open the drawer, use the metal object to pull the drawer by placing it on the V so it will be attracted by the magnet inside the hole. You could even cap the top of the hole with a matching wood plug so the top of the hole wouldn't show. Or better yet, drill the hole up from the bottom and then press a round plug into the hole so the magnet won't fall out. Make the plug so it is removable so you can replace the magnet should it lose it's magnetism.

The plug could be just a brass setscrew that would self thread itself into the wood if you drill a hole just a little smaller than the setscrew. I would use as large a magnet as possible that would be determined by the thickness of the front of the drawer/tray. You could use more than one magnet side by side, actually. You would want lots of pulling power in the event the drawer gets loaded with stuff.

Marv

Re: Help with ideas

#60

Opps....

Marv

Wiley,

I just reread RJ,s suggestion....what I just suggested is pretty much what he suggested. Same concept with a few minor differences..sorry RJ

Marv

Re: Help with ideas

#61

Re: Nother idea....really simple

Wiley Horne--So. Calif.

Hi Marv,

What you just described is the first thing I'm going to explore with the magnets. It is what RJ Whelan was talking about.

Actually the tray front is thin at 3/16", but the tray base is almost 5/16", and that's where I'll try to hide rod magnet(s). Alternate choice is to build up the front to hide a 1/8" thick round.

The reason I mentioned using the magnets in repelling mode is that it tied into Marv's thought, but also because that approach can lead to a self-contained solution, with no auxiliary pieces to get lost over time.

LV shipped today; will report back later.

Thank you very much for the idea!

Wiley

Re: Help with ideas

#62

Hidden Latch Idea - Magnets of Course *LINK*

charlie belden

Late to this one but here goes.

Faced a version of this one doing an LP cabinet with my youngest.

He wanted a cabinet with no visible way to get into it. We used 1/4" birdseye maple for the front and used magnets and the ply's springyness to have it pop open when the magnets were pushed out of shallow holes in the sides of the cabinet. You can put a cylindrical magnet like the ones from Lee Valley in the rear corners of the drawer and a sprint metal strip behind the drawer to keep the magnets in the hole in the side of the cabinet. A magnet held against the outside of the cabinet repels the magnets in the drawers and the spring pushed the drawer open.


This idea requires a magnet "Key" to open and lock the drawer. Built that into the cabinet like this




More about this idea for a cabinet here

Re: Help with ideas

#63

Re: Hidden Latch Idea - Magnets of Course

Wiley Horne--So. Calif.

Charlie,

Thank you! And congratulations on the father/son adventure!

I particularly liked how you found a way to make the key integral to the piece, so it wouldn't get misplaced.

I have magnets arriving Friday and hope to make progress over the weekend. Right now, my first thought is (a) hidden magnets and (b) a tray that gently slides out an inch or less when the door is opened (no catch/release mechanism).

Undoubtedly there will be some weird surprises, so am planning on doing considerable experimentation before surgery begins.

Thanks again,

Wiley