Re: Veritas Plane vs. Lie-Nielson
Greg Sloop, Portland Oregon
>I went looking for my past posts on this subject, but frankly I can't find the one I want. (BTW: Google searches WC a lot better than WC searches WC...)
I got the LN 62 some time ago. I really loved it. Very nice plane, but I did have some peeves about it.
When LV started selling the 62.5 I used a friend's 62.5 for a few weeks, and decided to sell my LN on the bay and get a LV. That I did, and I've been very, very happy with the LV version.
Here are some comments I've made in that transition.
"The adjuster is much finer, IMHO, than the LN62. I also always feel there's just a bit too much lash in the LN, and that it's not fine enough in pitch. The LV62 adjuster I keep liking more and more. I'm not much of a guy to use the lateral adjust, thus it's mostly wasted on me - but if you can't sharpen your irons straight or like a lateral adjust, the LV has a very nice one."
"One pet peeve on the LN is the iron cap. The LN uses a simple brass screw with a bit of a point on it. What I've experienced is that unless you crank it down quite hard, it will often come loose. Often you won't notice until the iron starts to chatter. Then you check the cap and find it's way loose. Tighten and the chatter goes away. This isn't a huge problem, but it can be annoying.
The solution to the above problem is to crank the iron cap down. But when you do, you can't make any projection adjustments - the iron is just being held too tightly to make any adjustments. Now, perhaps that's as designed, and I'm a moron, but I don't think that's the case.
(You can often find a happy medium where you don't get a loose cap iron and can still adjust projection, but it can be hard. More than occasionally, I find I'm unsuccessful and the cap iron is either too tight to allow projection adjust or too loose to stay firm, and it works its way out.)
The LV has a similar cap, but it's longer - which gives more of a fulcrum and the brass screw has a "foot" on it. (I don't know what else to call it. Perhaps some pictures later...) The cap doesn't come loose, and with a moderate tightness on the iron cap, you can still easily adjust projection of the iron without fussing with the tightness of the lever cap, both before and after. "
"The little screw that keeps the adjustable foot from banging into your sharpened iron is very nice. However, when taking a fine cut with the mouth wide open - not something one would often do - the shaving often gets caught behind/underneath the screw and stops up the mouth. This is easily fixed by closing the mouth down. I'm not sure how it will work when taking a thick shaving with the mouth wide open it may still occur - I've not tried it. I suppose you could always take the screw out if you found it annoying on a regular basis."
Update note to the above. If you don't leave the screw all the way out, it doesn't catch shavings. Run it in against the foot when you're taking thin shavings and it doesn't catch the wispy ones any more. (If I wasn't so dim, I'm sure it wouldn't have taken Rob Lee to let me know to do this. I asked via email and he was very gracious to tell me *I* was borked, not the plane. *grin* [Actually Rob was very diplomatic as usual.])
"The front adjustable shoe on the LV adjusts very nicely. I think the LV that I have slides more easily and freely than the LN.
The LN does have the cam ring to help adjust the shoe, and the LV doesn't. Given how freely the LV slides, it isn't a problem at all. However, if the LV one was a bit stickier, it could be a problem. (If the LV engineering/manufacturing QC is good, I don't expect this to be a problem.) [Update: I've not heard of anyone complaining about this, so LV apears to be doing well here.]
The better feel and heft make it easy to get full length shavings - it seems easier to power through a full cut. The finer adjustment also helps, as you can more easily/quickly pick exactly how thick a cut you want to take"
I prefer the longer toe on the LV version. It's quite handy when you're touching up short pieces. This is a very substantial issue for me.
----
A few further comments.
These apply when you look at the "set" of planes from LV and LN as a group.
LN: 62, 164, Jointer
LV: 62.5 Heavy smoother, Jointer
As has been noted, the irons on the LV serious of bevel up planes all transfer between all the three of that series. *Heavy* smoother (not the smaller one), 62.5 and jointer. Since I have at least two angles for each plane, that save a bundle since I'm not required to have two irons for each plane. If I choose to have two each, I have more irons to run through before I have to sharpen again.
The LN 164 smoother has an annying attachment to the blade for adjustment purposes. To sharpen you have to take it off, and will have to transfer to another blade if you only have one. Minor irritation, but significant, at least to me.
The LV jointer has an adjustable mouth, the LN does not.
===============
Given all the above, and given the advantages of a "set" of planes, IMO, the very clear advantage is to LV - at least from a utilitarian view.
One last item. Some people have more of a fetish relationship with their planes than I do, and don't care for the "look" of LV. If that's a problem for you, then look carefully and see if you don't mind the LV stuff. Frankly I don't much care what they look like anyway, but I don't think they look half bad anyway.
Also, as has been mentioned, some don't care for the LV tote. Myself, being the oaf I am, I guess, can't tell any real difference betwixt the two. But you might.
If I were to try something, I'd buy the LV and see if you liked it. If not, send it back. I suspect you will.
Cheers,
Greg