Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

refinishing vintage Shuffleboard table

Posts

Re: refinishing vintage Shuffleboard table

#76

Re: Wax on - wax off

Edward S

ok, now i have another problem. i have 2 low spots on the board due to my noober stripping! I gauged the table in 2 different spots.

I thought the poly would level these spots out, fill and level?? what?

anyway can i spot fill these small areas, and just feather out??

dont know what to do now.

Re: refinishing vintage Shuffleboard table

#77

Re: Wax on - wax off

Edward S

do you recommend using a scraper? i was told by someone else to use one to level the surface.

but i never used one, i dont know?

Re: refinishing vintage Shuffleboard table

#78

Leveling

David Yoho

I'm afraid this issue is something I can't help you with. There are guys on here that might be able to help but I think I would start a new posting, briefly describe the problem, and see what answers might come along.

Technically I know there is a way to do this but I haven't had to do it so I can't tell you how. I would think sanding would get you there better than using a card scraper that you have no experience with. This doesn't sound like a job for a power sander. Think automotive body work and blocking.

Starting a new posting will move this to the top of the list and make it easier for folks to see and read. Your responses should be better this way.

Re: refinishing vintage Shuffleboard table

#79

Re: Leveling

Edward S

your right, i do not want to go the scraping route being i never handled one.

i light sanded the 2 low areas, cleaned and hit with some undiluted poly.

so far so good, i dont see any indents yet!

after it dries i guess i will try and feather and then apply final coat.

i was thinking about applying a thick coat using the undiluted poly, what do you think?

Re: refinishing vintage Shuffleboard table

#80

What have you learned

Bill Tindall, E.Tn.

Didn't this all start with your lack of success using undiluted varnish? Nearing the end of a long process is not the time to start experimenting with new techniques.

Why would you want to use undiluted varnish? Presumably the thought is that it will build faster- at the expense of bubbles and poor leveling, more sanding, etc. If you are diluting 1 part solvent to 3 of varnish (more of less) the build will be at a rate of 75% of the undiluted varnish. Looks like as long as this event has carried on that this is a tiny sacrifice in the path to an end.

Re: refinishing vintage Shuffleboard table

#81

Re: What have you learned

Edward S

Hi Bill, wow i think we ran out of room! LOL!

But in response to your last post. Yes, i agree laying out full strength poly isnt good for the bubbles and leveling. But after stripping last time i managed to gauge 2 areas. Well these 2 areas never leveled out after about 12 coats. I dont quite understand it, i really sprayed the lacquer on heavier in those areas. I even tried putting extra drops of poly on the areas during application.

So yesterday i applied undiluted poly to the 2 areas, very thick! I think it may have worked, looks good this morning after light sanding! So in order for me to bring the level up to these 2 areas i decided to put a full strength coat of poly down.

But i will never do that again unless i have to, it was very hard to smooth out, way too thick!

I am hoping after sanding again i can apply 1 more thin diluted layer.

I will take some pics. later and post, thanks again!!

Edward S.

Re: refinishing vintage Shuffleboard table

#82

Re: Wax on - wax off

Edward S

David or whovever read this, i finally got my last coat on without any contamination , much bubbles or dust! it was Sunday morning since the final coat.

I want to get this final step right. After at least 15 coats of poly, i have way too much time in this shuffleboard to screw it up now!

Anyway, i have 600 grit and 1500 grit sandpaper i bought. Assuming i sand in circular motion with the 600, then 1500.

After that then what? How do i get a shine? just buff? i do not own a buffer, but thinking about buying a applicator and buffer pad for my Bosch ROS.

If i buff, what solution do i buff with?

Sorry if this was mentioned earlier, i cant remember, i have a little CRS.

Re: refinishing vintage Shuffleboard table

#83

Practice

Bill Tindall, E.Tn.

"I want to get this final step right. After at least 15 coats of poly, i have way too much time in this shuffleboard to screw it up now! "

Well said. The obvious conclusion is to stop doing experiments on the product. You have demonstrated patience and determination. Use it to proceed safely and not screw up what has been done.

Prepare a test piece. After the finish has cured to be hard, get the next steps right on this test piece before proceeding.

We have no idea what you want for a final appearance or how level it needs to be. If it was furniture 4/0 wool and wax might be just fine. I have previously described how I get a mirror finish on furniture. The bottom line is that you are going to need to experiment on this unique job to come up with a result that suits you.

Re: refinishing vintage Shuffleboard table

#84

wait a month

Dick Coers

If I had put 15 coats of poly on anything, I would wait a month or more before trying to buff it. That's a ton of finish! But remember, you can only sand or polish that 15th coat. If you cut through it with sandpaper, you'll see another layer. Other finishes can melt into the previous coat, poly doesn't. I prefer Abralon and soapy water on the random orbit compared to a buffing pad.

Re: refinishing vintage Shuffleboard table

#85

Re: wait a month

Edward S

I really cant wait a month, it have to get it out of my dining room! anyway what if i hand buff it? Today is Thurs. , which is 4 days since last coat. I was thinking about sanding today with the 600,1500.

Re: refinishing vintage Shuffleboard table

#86

Depends

Bill Tindall, E.Tn.

No having any idea of what the final objective is for levelness and luster it is impossible to comment on you suggested plan. If the multitude of layers are cured hard and you are satisfied with the result of 600/1500 all is well. If the result is not satisfactory you should have followed the advice you asked for.

Re: refinishing vintage Shuffleboard table

#87

Re: Depends

Edward S

well yea, i want the surface as flat and level as i can get it, what are your suggestions to get this? please do not say a card scraper, not gonna happen!

Re: refinishing vintage Shuffleboard table

#88

Re: Depends

Edward S

i was told to use carnauba wax after sanding, is this good to use? others have said to use something like Johnsons paste wax.

Re: refinishing vintage Shuffleboard table

#89

Wax

Bill Tindall, E.Tn.

Carnauba wax is very hard and durable. I use it on machine surfaces like saw and planer. I make my own by dissolving carnauba wax flakes in mineral spirits or toluene. Johnson's is less hard/durable but easier to deal with.

A normal sanding sequence is to skip one grit size in the sequence. So for example one sands 400, 800. 1200 etc. , or 320, 600, 1000, etc.

Re: refinishing vintage Shuffleboard table

#90

Re: Wax on - wax off

Edward S

well, finally done the shuffleboard! Thanks to all who helped me! i learned alot. here is a pic. of finished product!

Re: refinishing vintage Shuffleboard table

#91

Re: Wax on - wax off

Edward S

well i guess im a noob at posting pics here too, lets try again!


img

Re: refinishing vintage Shuffleboard table

#92

Do we get an invitation to come play?

Bill Tindall, E.Tn.

I forgot how long these things were. That's a lot of finishing

Re: refinishing vintage Shuffleboard table

#93

Re: Do we get an invitation to come play?

Edward S

of course! im in Gilbertsville, Pa, the gameplay is great on this table! I love this game!