Re: Ounces!
Edward S
ok, i had him add 2 drops to 3/4 gallon. hope this works!
Knowledge You Can Build On — Est. 1998
Re: Ounces!
Edward S
ok, i had him add 2 drops to 3/4 gallon. hope this works!
use manufacturers recommendations
Bill Tindall, E.Tn.
don't guess
Re: use manufacturers recommendations
Edward S
manufacturer for who? the fisheye remover or poly? no help from Minwax
but anyway, i guess that wasnt enough , still came through!
Re: use manufacturers recommendations
Edward S
i guess that wasnt enough fisheye remover, guess i'll wait a couple days and make stronger?
Re: use manufacturers recommendations
Edward S
Ok, made a stronger potion with the fisheye remover, looks pretty good, maybe 2 tiny spots. I also discovered the dust problem i was having was from my electric heater blowing in the room!
This app. looks best yet!! Only a few dust particles.
You are learning a lot
Re: You are learning a lot
Edward S
maybe 1 or 2 coats left and i hope to be Golden!!
So i have bought #4 steel wool for dust nibs after final coat, do i sand entire surface with this? or just nibs? Also, after few days do i rub with a compound, then past wax?
I was told that by a new friend i met, the guy who gave me the fisheye.
He stated to use a rubbing compound to rub out finish, then past wax after that. is he right?
Re: You are learning a lot
David Yoho
I've been following this thread from the beginning. As far as the steel wool goes, I wouldn't use it unless your intent is to give a final appearance of a lower sheen than you started with. For dust nibs (those you can feel when you run your hand over the dried surface) I like 600-grit wet/dry paper. I usually cut a sheet into four equal pieces, then take one and fold it in half and go over the surface by hand. You only need to use very light pressure. You only want to knock down any points from the nibs but not leave scratches. Then, if you want, you can use a paste wax like Johnson's Wax to give it a final shine. CAUTION - don't use a paste wax like Briwax that contain the solvent Toluene. It will eat a new finish. These waxes should only be used on totally cured finishes.
Re: You are learning a lot
Edward S
The fisheye remover is not working too well. I just put another coat on , which is about my 10th!. Anyway, i can see the contamination on top of the poly, it looks like bubbles. When i flick it with my brush, it looks like water hitting oil.
So, here is my question now. Can i sand when done starting with 320, then go up in grits to rub out one another? and then use rubbing compound after that with buffer?
I was also thinking about putting a clear epoxy on top?
Or do you think i should stop now and let dry, and strip?
dont know what to do now!!
Not what you want to hear
David Yoho
I know at this point you don't want to hear this but I seem to remember (without going back through this thread again) you getting advice to strip and start over. That's when you should have done it because it would have saved you much time and effort.
I remember thinking then that you were probably going to learn the hard way. For what it's worth, take the hit, strip down to bare wood, and start new using what you have learned through this process. I bet your outcome will be what you have been looking for from the start.
I've done a lot of stripping through the years and I rely on only one product - Bix Varnish & Stain Remover in the orange and white can. If you do use it you will need to use neoprene gloves and other safety gear. It's the best stuff I've found for stripping any finish. Remember - the friendlier the finish, the slower it works and the more it takes.
Re: Not what you want to hear
Edward S
thanks David,
you are right, its time to strip! How long do you think i should wait? I just coated today, hoping to start stripping tomorrow! Got some in garage leftover, it was from Lowes.
anyway i am going to Lowes and buying this orbital sander by Bosch, i can use a 10 off 50 code for ok deal.
http://www.amazon.com/Bosch-ROS20VSC-5-Inch-Random-Carrying/dp/B00BD5G9VA/ref=sr_1_12?s=hi&ie=UTF8&qid=1421094242&sr=1-12&keywords=5%22+orbital+sander#customerReviews
Now i have been thinking about what i did wrong the first couple times. I guess i should of bought a degreaser of some sort, i was told to get Maxsolv 5900 to clean the silicone off first.
After this i was going to buy some of Zinsser Sealcoat Shellac (dewaxed), but i do not know if i should buy spray can? So just in case if there is any silicone i dont spread it around with a brush, i dont know? or can i just buy quart and spread on? I might be safer spraying a can of aerosol stuff right?
Do i sand between this stuff?
Now after this point i guess i should add the #'s and lines. This time i was going to use a carpenter's pencil instead of the thick vinyl.
I was going to again use oil based poly, but this time was going to buy a quart of Varathane.
I was hoping to only use 3 or 4 apps. this time instead of the 10+ i used with the high build minwax formula.
Please let me know everyones conclusions. This shuffleboard is severely contaminated with silicone!!
Re: Not what you want to hear
David Yoho
It's okay to start stripping as soon as you're ready. Polyurethane is harder to strip than plain varnish. It may take you several applications before getting it all off.
I don't think you'll be able to remove the silicone contamination with anything once down to the bare surface but sealing it in might be the way to go. If you can't find a quart can of Seal Coat nearby then the Zinsser Spray Shellac is also de-waxed and would work. The only sanding I would do after the shellac would be a light sanding (light pressure) to smooth the surface. Then apply your poly and see how it goes.
I have never had to deal with silicone contamination but I think the idea of sealing it in sounds like it should work. At this point you wouldn't have as much to lose if you had to start again.
Re: Not what you want to hear
Edward S
thanks for help David!
Varathane sells aerosol cans of poly, just wondering if i should try and spray? instead of brush on?
also, i guess i could use water based? its rock maple wood shufflboard.
Re: Varathane
Ron in Sterling, CT
I have used gallons of Varathane over the years. It is one of my favorites. I prefer to brush it on. Thin it just like Bill recommended for the Minwax urethane in one of the earlier responses. Good Luck.
Ron
Re: Not what you want to hear
David Yoho
Forget the spray. Get the solvent version and brush it on.
Re: Not what you want to hear
Edward S
Should i buy a little Zinsser dewaxed shellac? or apply my Minwax sanding sealer , i have half can left? I ready bad reviews about Minwax sanding sealer.
Stripping
Bill Tindall, E.Tn.
Urethane varnish strips easily with any stripper that costs a lot providing the cost reflects that amount of expensive methylene chloride in the product. Because the finish is cross-linked it softens and scrapes off in one nice layer like removing a coat...... when using a methylene chloride stripper.
Apples and oranges
David Yoho
You're talking about two different things. Use the de-waxed shellac to seal in the contaminate before moving on to your poly. If you need to stain the wood, do it before applying the shellac. I can't see a reason for using the Minwax wood conditioner before staining the surface of the table. Actually, I never use that stuff in my shop anymore. There are better methods and products. Remember - the reason for the de-waxed shellac is to hopefully seal in the silicone residue. You're not using it thinned as a wash coat to control the amount of stain absorption in this case. You want it full strength and probably several coats.
methylene chloride
David Yoho
Yes, that's the good stuff and what it takes to get it done.
Re: Stripping
Edward S
But what do you guys think about getting the aerosol spray shellac? So i dont move the contamination around with a brush? or should i just buy a quart and reapply a few layers with brush?
that is another thing, what if my brush is contaminated with silicone?
Re: Stripping
Edward S
also if i get the Varathane, should i use the water based or oil? does it matter??
Re: Stripping
David Yoho
I like the idea of spraying it to avoid brushing in this situation. Also, I'd favor using the oil based urethane. Nothing wrong with using either type after the de-waxed shellac because either will stick to it. My personal preference is oil based though.
Re: Stripping
Edward S
i've read the oil based poly has an amber color, the maple wood is whitish, so not sure , i might go with water based.
Re: Stripping
Edward S
Also, when should i use the pencil to add the #'s and lines? After the few coats of shellac is on im assuming?
Pencil marks
David Yoho
If it were me and given you are probably going to spray the shellac, I think your best bet would be to use the pencil first, then spray your shellac, then apply the poly. This way you avoid smearing the pencil marks with the application of any finish.