Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Need a circular saw recommendation

Posts

Re: Need a circular saw recommendation

#26

Re: Need a circular saw recommendation

Joanne in Point Pleasant, PA

Thanks, Joe. I'll take a look. Sure beats trying to invent something. While that is fun to do, it takes time I don't have.

Re: Need a circular saw recommendation

#27

Joanne and circular saw recommendation

Stuart Johnson

Now that you have used the Ridgid 6 1/2 Fuego saw for a bit what is your opinion?

Re: Need a circular saw recommendation

#28

Re: Joanne and circular saw recommendation

Joanne in Point Pleasant, PA

Hi Stuart,

I like the saw a lot. It is light, small, sharp, quiet, and cuts very nicely. The one thing I marvel at (and do not like) is the odd-shaped port at the back. The dust shoots out through a small, squarish hole--right at me. Not an easy shape to cobble a dust chute for, but I will try. Other than that, it is a great saw and I recommend it. I put a finish/plywood blade on it to cut some plywood and some closet doors--it left a beautiful, clean edge.

Re: Need a circular saw recommendation

#29

Re: Joanne and circular saw recommendation

Stuart Johnson

Thanks. I'm getting ready to start a new project and think it's time to retire my Penncraft. Rremember when J.C. Penny sold hand tools and would give anyone that was breathing a charge card? Something lighter will be welcomed.

Re: Need a circular saw recommendation

#30

Re: Joanne and circular saw recommendation

woodenleg

If you have a friendly auto parts store you could take the saw in there and see if they may have a heater hose or a plug that can be inserted and then tighten. That is what I had to do with a saw that I own. Dave

Re: Need a circular saw recommendation

#31

Re: Joanne and circular saw recommendation

Larry in NW OHIO

Joanne If you could post a picture of the saw with the outlet showing, maybe someone here could come up with a solution. Larry

Re: Need a circular saw recommendation

#32

Re: Joanne and circular saw recommendation

Joanne in Point Pleasant, PA

Great idea! I'll do that tomorrow when I get out in the shop. Thanks!

Re: Need a circular saw recommendation

#33

Re: Joanne and circular saw recommendation

Jim Dillon

Joanne,

If you get FWW, the August 2011, No. 220 issue had a cobbled-together solution for a portable sander with a similar rectangular dust port. Check out page 15 for a picture. If you don't have that issue, basically, the author carved a wooden adapter with a custom-fit hole on the sander side, and a circular hole on the opposite side for the dust-collection hose. Depending on the snugness of the fit, duct tape might be needed. Not the most elegant solution, but it might be worth a try.

Jim

Re: Need a circular saw recommendation

#34

Re: Joanne and circular saw recommendation

Carol Reed, Strawberry, AZ

FWIW, Joanne, my brother heated PVC pipe/fittings with my heat gun and then shaped them to fit. He used heavy gloves and a couple pieces of plywood, stretching and pushing, to make my rectangular rain downspouts fit into round drain pipe. Looks very professional. There was no store-bought adapter available. Maybe there is a PVC fitting that will fit your vacuum hose. The other end could then be molded to fit the saw. Might only cost a pittance to try.

Re: Need a circular saw recommendation

#35

Flap?

Jerry Gibbs

Would a flap of some sort work to deflect the chips. You could experiment with tape and various flap materials, such as neoprene etc.

Re: Need a circular saw recommendation

#36

Re: Joanne and circular saw--chute pics

Joanne in Point Pleasant, PA

Thanks for all of the great ideas to help deflect the dust on this saw. I took some pics of the chute/slot when I was out in the shop yesterday. It is pretty small and shaped oddly. And there is not much room before the blade guard inside. I think I will either have to carve something to fit or do as Carol suggested and melt some pvc to fit (brilliant idea, that! we had to do that once to repair the workings of a doorknob and lock).

If anyone has any other thoughts, I haven't pulled out the torch yet, and would love to hear them.


Re: Need a circular saw recommendation

#37

Re: Joanne and circular saw--chute pics

Larry in NW OHIO

My first thought that I would try, is to get a pvc pipe big enough to straddle the guard over the hole, I think I`d maybe try to file the hole a little bigger, cut out the top and bottom so it would slide over the hole and heat the pvc on the sides to flatten them and then get some self tapping screws and screw in from the sides to hold it. then kind of go from there to hook it up to a vac with a 11/4"hose. See Joanne how easy that was :D I hope you can understand what I meant. If you do explain it to me. Good Luck. Larry

Re: Need a circular saw recommendation

#38

Re: Joanne and circular saw--chute pics

FredD

Time is money , I would take it down to a Auto Parts store and tell them I need a deflector inserted in the outlet hole and maybe a radiator hose or something along those lines could be squeezed into the outlet for a tight fit. then put a PVC ninety into the hose.

If that won't fly , you might try cutting a wood block that is a snug fit and then cut a 45 degree angle from the right out side corner to the middle of the block and glue it in.

Sheet metal can be made to work like that also.

FredD

Re: Need a circular saw recommendation

#39

Re: Joanne and circular saw--chute pics

Joseph Mulherin

Looked many times at the pics and I agree with Larry on using the PVC pipe heating it and cutting to fit as needed. Certainly an easier way of doing it is found from our WC associates.

Re: Need a circular saw recommendation

#40

Re: Joanne and circular saw--chute pics

Kurt

This is quite a bit of money for what it is but if the width is right it'd sure be an easy fix for the Ridgid saw.

http://www.eurekazone.com/content/ez-dust-port

Re: Need a circular saw recommendation

#41

Re: Need a circular saw recommendation

Joseph Mulherin

Joanne, someone here mentioned fashioning a PVC chute to the opening by cutting slots and removing the shorter parts, then heat the long ends to fit your chute and screw them to the casing. Then you add a 90 or 45 deg elbow and your vacuum line or just an old sock to catch the shavings.

Re: Need a circular saw recommendation

#42

Re: Need a circular saw recommendation

Joanne in Point Pleasant, PA

Thanks, everybody. Les Winter emailed me the link to the Eurekazone chute--which is similar to the recommendations to cut and heat a piece of pvc pipe and attach with screws. Think I'll try that idea first. Now I just need the time to putter with it. I'll eventually post when I get it fitted out.