Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Drive centers

Posts

Drive centers

#1

Drive centers

Ryan

I'm looking at a new spur drive center and wonder what you all use. It will be for nat edge bowls up to about 12"diameter. Love the ones at Best Wood tools but too much for my wallet, so I'm considering the Big Bite from Oneway or Axminster Jumbo drive from Craft Supplies. Any other suggestions? Two prong or 4 prong?

I'm really tired of my current center acting like a drill!!

Re: Drive centers

#2

Re: Drive centers

Dale Gillaspy

Regardless of what center you use, try drilling a flat spot with a Forstner bit for the drive to grab onto if you are putting the drive on the natural edge.

Re: Drive centers

#3

Lyle Jamieson

Re: Drive centers

Lyle Jamieson

I don't like two prong drives. They damage the wood like a splitting maul. Do a bowl and it might have a crack in the bottom from the drive damage.

Re: Drive centers

#4

Re: Drive centers

Bill Howatt

I have a Big Bite and I think it is rather large for items much under 12".

Grind 2 opposing spurs off a regular 4 spur center. It will bite in better and you can align it with the grain which will also aid penetration. If you are putting it into bark it is helpful to drill a large hole in the bark (or chisel it away) with a Forstner bit.

The tailstock pressure should be frequently adjusted especially when you first start with the piece.

Bill

Re: Drive centers

#5

Re: Drive centers

John Lucas

I'm with Dale. Sharpen your current drive center so it bites well. Then either chisel away the bark below the cambium layer so it has a place to bite, or if you have a drill press drill it out with a forestner style bit.

Re: Drive centers

#6

Brad Vietje

Re: Drive centers

Brad Vietje

I have a 2-jaw (teeth?) version from Best Wood Tools, though I didn't remember it being expensive (prob 8 - 10 years ago). Mine was originally for my Supernova chuck, but I grab it in my Oneway Stronghold 50 mm profile jaws all the time w/out any problems.

I use it for "regular" utilitarian bowls, but it really works best for balancing the figure on natural edge bowls and vases. I align the 2 teeth with the bark/pith/grain direction, so I can tilt the wood between centers in the other direction to balance the low spots. I have not experienced any excessive splitting of the wood like Lyle has; maybe I don't pound it in as hard?

Safe spinning,

Brad Vietje

Newbury, VT

Re: Drive centers

#7

Steb Centers.....

Wally Dickerman in Arizona

I have Steb centers in a couple of sizes and like them. I find them easy to use and they don't damage the wood.

Re: Drive centers

#8

Re: Drive centers

Bill Jacksonville, NC

Which way to mount wood on a lathe safely and give greater ability to achieve that design you have in your mind or let you design as you turn? Simple inexpensive MT-2 two-prong/spur drive center!

Before we mount a piece of wood on lathe (method used) have to think about WASTE ALLOWANCE.” Your waste allowance addresses both safety and design options! Waste allowance simply amount of wood you cannot turn or damage to wood you address before finishing the piece. Simple two prong/spur drive center affords both safety & design options with least amount of waste!

Own two different prong/spur centers one with adjustable point & one without. Bought years ago to replace crappy OEM four prong/spur centers and have served me well. Use the fixed two prong/spur center on dry wood spindle turning and adjustable point center on heavy wet wood. Only real adjustment can make is loosen hex screw to remove point from drive center to straighten or sharpen.

My favorite two prong drive center bought from Craft Supplies before they had the Precision Machine 2-Prong Drive Center.

Re: Drive centers

#9

Re: Steb Centers..  Where from?...

david

After about 11 years of turning I finally got a Steb center and then wondered why I hadn't gotten one sooner. Interested in getting others in different sizes. Where are they available from?

TIA

Re: Drive centers

#10

Re: Steb Centers..  Where from?...

Wally Dickerman in Arizona

David, I got mine at Craft Supplies. There are some knock-offs at a lesser price but I don't know anything about their quality. I just bought the best as I usually do with tools.

Re: Drive centers

#11

Dick Hines

Re: Steb Centers..  Where from?...

Dick Hines

I use a 4 spur drive center I got from Woodcraft. It holds very good. When I mount a blank I will drill a hole just larger than the drive center. Then flood it with thin CA. After it dries I pound the drive center in. Very seldom do I have a problem with I spinning.