Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Trent Bosch Visualizer

Posts

Re: Trent Bosch Visualizer

#26

Try This:

Mark Mandell - Gone Round In New Jersey

Replace the laser pointer on a boring/hollowing rig with the camera and plug the camera into the laptop so you bring up this nice picture of your cutter (a Hunter carbide for S&G). You can move the camera and cutter assembly all over the place but the only part of the picture that changes will be the background.

Now take a black dot the same size as the cutter and place it on the vid screen so it just covers the round Hunter cutter.

Run the cutter into a jar and the picture of the tool shaft and cutter will disappear but the black spot will remain. You will see the tool shaft and the outside surface of the jar

Move the assembly so that the cutter touches the sidewall of the jar.

On the monitor you will see the jar and to the right of the outside surface of the jar you will see the black spot that you put on the monitor. The distance between the edge of the spot and the outer surface of the jar will tell you how thick the wall of the jar is at the point where they touch.

When you use a laser, you set a gap between the laser dot and the cutter. When the dot "drops off" the side of the jar, you have reached your assigned wall thickness.

The camera's advantage is that for any given point on the jar's walls, high, low, bottom, you always know where the cutter is making contact. The laser's advantage is that you've locked in a given distance between the spot and the cutter and you don't need to eyeball the thickness on the monitor's image. The laser's disadvantage is that your set distance is only to one point on the round cutter, say at 9 o'clock. When you move to say the bottom of the jar, you have to retract the rig and reset the laser dot to 12 o'clock to keep the same thickness goal. With the camera/black dot rig you don't reset anything as you always have a measure of the wall thickness at the contact point.

Re: Trent Bosch Visualizer

#27

well stated Mark, thanks

Dick Coers

I prefer to mark a wall thickness around the cutter when I use the camera. At first I laid up a scale next to the cutter, and made the mark. But I found my system was basically one to one scale. So now I sketch around the cutter by eye for the wall thickness.

Re: Trent Bosch Visualizer

#28

Re: I've shown it on WoodCentral before

John Jordan

There is no software in Trent's setup. Just focus the camera on the tool. And just a tv or monitor with RCA jacks will do IF your camera has the same-Trent's does.

I'm not sure why Dick got some crap over this, but some folks should mind their manners.

Thanks, Dick.

John

Re: Trent Bosch Visualizer

#29

Possible Error?

Mark Mandell - Gone Round In New Jersey

Dick,

There appears to be a slight parallax error in the monitor image unless the center of the camera's lens is set dead-nuts plum with the working edge of the cutter as the camera's view of the outside wall of the jar will be at a slight angle giving a "horizon line" in the video that is slightly above where the cutter makes actual contact. For woodturning, where someone isn't making a wall thickness of a 1000th or two, it probably will make little or no difference, but it's well to be aware of the difference when eyeballing the wall thickness on the computer monitor.

Re: Trent Bosch Visualizer

#30

Re: Possible Error?

Dick Coers

I'm aware Mark. One guy I know uses a length of ball chain as a plumb bob system to locate the camera directly above the cutter. He made an adapter that snaps on the end of the camera, then pops off when he's ready to turn.

Re: Trent Bosch Visualizer

#31

Cutter Vision *LINK*

Stuart Johnson

I just watched a video about CutterVision. I think it is the same idea and shows how it works. I still have a hard time getting it set in my mind but I have stopped thinking of it as magic.


CutterVision Video

Re: Trent Bosch Visualizer

#32

Re: Try This:  Thanks

Barry Irby

OK, so what you are saying is it APPEARS the background (the vessel) moves and the dot/cutter remain stationary?

I want to see one in person and play with it. I'm not even skeptical. I am just struggling to visualize the Visualizer.

Is it like the little car image on my GPS? The car sits still and the map flies by under it at 70 miles and hour?

Re: Trent Bosch Visualizer

#33

By George!

Mark Mandell - Gone Round In New Jersey

Awee thinks e's gawtit!

With the lathe running and the cutter engaged, what you'll see in the monitor is the outside surface of the jar and the black spot a certain distance away from the line of the left profile surface. As the wall gets thinner, the spot will move closer to that outside line.

You can also put a thin circle around the black spot, say 1/16 to 1/4" larger, as your thickness "gauge" such that when the thin line "touches" the outside of the jar, you have reached your chosen wall thickness.

Given the vibration of cutting coupled with all the joints needed for the camera boom, it's probably a good idea the retract the cutter from time-to-time to make sure that the black spot on the monitor is still precisely set over the image of the cutter.

Re: Trent Bosch Visualizer

#34

Re: Cutter Vision

Dale Bonertz

Keep in mind that the magnification of the camera plays a role. With Trent's system if you want say a 1/4" wall thickness you want to draw the line around the cutter at 1/2". His camera gives a very clear picture on the screen and I am assuming it is the optimum magnification for his tool thus the line versus actual thickness ratio.

Also someone brought up needing overlays for the screens. Trent's screen does not need overlays just make sure you use the correct type of marker and it wipes right off.

Re: Trent Bosch Visualizer

#35

Re: As Ricky would say, I've got some "splainin" t

Don McLeod

When I started reading this thread, I couldn't visualize how this could work, but there have been a few explanations that brought it into focus. Then after looking at Dick Coers camera I realized I had something similar in my tool box It's an inspection camera that uses a laptop for a monitor, don't know if it will work but it's worth a try.

Re: Trent Bosch Visualizer

#36

That's what my camera is, yours should work fine


Re: Trent Bosch Visualizer

#37

Re: That's what my camera is, yours should work fi

John Jordan

Does anyone remember where the little square cameras everyone was using for demos (all the clubs had them). They were cheap and could be focused, and didn't need a computer-just plug into a TV/monitor.

John