Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Need a new drill

Posts

Need a new drill

#1

Dan Jechura

Need a new drill

Dan Jechura

I need a new drill for sanding bowsl. What do you use? 55 deg angle or 90deg. Battery or electric. I would like variable speed.

I've been useing a battery portacable nad the battries are dying.

thank you for your help

Dan

Re: Need a new drill

#2

Re: Need a new drill

david

I got my 55 degree corded close quarter drill from a vendor at San Jose. Think it cost about $45. I treat them as expendable, because the fine sawdust will eventually win out and cause malfunctions, even if I blast out the vent slots often. The San Jose purchase no longer has a functioning reverse. Will get another when this one goes kaput. Similar drills available on eBay for under $40.

Re: Need a new drill

#3

Ric Taylor

Re: Need a new drill *LINK*

Ric Taylor

Here is what I use. It has been going strong for about four years with no problems, I just blow it out occasionally. It's reversible. I paid extra for the jacobs chuck feature and it works great for me. There is no brand name on it, but it is still going like it is brand new.

Ric


http://thesandingglove.com/Angle-Head-Drills.asp

Re: Need a new drill

#4

Dick Hines

Re: Need a new drill

Dick Hines

I have one these drills. It has been working fine for a while. Can't remember when i got it. After I use it I blow the dust out. I shoot every place dust can get. Don't forget the direction switch. Dust collects in there.

The next time my compressor dies I will get one big enough to use air tools. They don't have the openings that an electric drill does.

Re: Need a new drill

#5

Re: Need a new drill

Jeff Smith

For most of my tools, I usually pop for the more expensive tools - figuring you get what you pay for. When they break I can usually get parts to fix them and keep them running longer than the cheapo ones. The prime exception to this is the right angle close quarters drill I sand on the lathe with. I get the cheapest one HF sells - I think it's $29.00. I always spring for the extended protection plan. They have always lasted two years - the length of the plan. Take it in and get a new one.

I'm on my fourth one now. Blow them out once in a while and they're good to go. I did try the more expensive version with a keyless chuck, but it didn't last as long as the cheaper one.

Re: Need a new drill

#7

Re: Need a new drill

robo hippy

I use the angle drills. Mostly they are better at getting inside a bowl than the right angle drills. I think the biggest cause of the bearings going out is that they are drills, and we use them more as grinders. I am thinking we need a flex shaft that will run off a variable speed mini lathe. You could run 5 inch discs no problem. Working on that one.....

robo hippy

Re: Need a new drill

#8

Re: Need a new drill

John Lucas

I e been using the same dewalt standard corded electric drill for almost 12 years. It dean about $64 back then. I bought a back up at the pawn shop a few years ago but this one just keeps on going

Re: Need a new drill

#9

Re: Need a new drill

Barry L Elder

You get what you pay for! In 1980 I was working for a Hardware Chain down here and had a need for a decent drill. I talked to our Power Tool Service Dept. and he advised that I purchase a discontinued Rockwell 3/8 chuck VS that listed for $129 and had been discontinued. Since I was an employee I paid about half price. About 20 years later the VSR switch died and I bought another switch for $37. About had a heart attack! It's still running and it's an antique! Anybody interested? :)

Re: Need a new drill

#10

Re: Need a new drill

jim breeden

I'm with Jeff. I have the same drill, which started to make a lot of noise last week. Thinking it was a bearing, I disassembled and found that the drive shaft from the motor to the head was worn. I stuffed it full of paper towel, added some CA, and viola, no more noise! Runs just like it did 3 years ago.

Re: Need a new drill

#11

drill

Darryl

I guess I am a tool junkie. I have an old Milwaukee 55, a Sioux of the same vintage. Like them both. Also bought a cheep knock off for about $30. I also have a Harbour "fright" central machinery 90. the HF is short in the drill part and does just about what the others do. I kinda like the HF one because the balance seems to be better. the Milwaukee's do need to be blown out whereas the HF does not since the vent holes are in a different position. I would certainly go for the cheepies ( under 40$) regardless of the shape you get.

Re: Need a new drill

#12

Becareful Blowing Out The Dust

Stuart Johnson

After reading one of these threads about blowing out the dust I did just that to my Milwaukee. I have no idea if the pressure was too high but the drill was dead. I had been using it and it was running fine. All I can think of is I blew something loose but have no idea what. After taking it apart and then reassembling it worked again. I now use a lower pressure.

Re: Need a new drill

#13

Re: Becareful Blowing Out The Dust

John Lucas

At one point I started to buy one of the angle drills that seem to be popular among turners Then I started to hear about all the problems with bearings going bad and I'm glad I stayed with my Dewalt I haven't done a thing to it I. All these years. I used to buy the $39 black and Decker drills and would go through one in about a year.

Re: Need a new drill

#14

Re: Need a new drill

Phillip Medghalchi

Dan, My Millwakee died and can't get parts for it. I went to Northern tools and the have one for $59.95 and it comes w/ 5yr warranty. They said anything happens just take it in and get new one. It;s called Klutch.

http://www.northerntool.com/shop/tools/product_200452870_200452870

That's $60/60 mos= $1/mos> i think that's a reasonable spendable.

Re: Need a new drill

#15

Re: Becareful Blowing Out The Dust

Dick Coers

I'd guess that a particle got under one of the brushes, or a brush slid out a bit. Just a guess of course.

Re: Need a new drill

#16

Re: Becareful Blowing Out The Dust

Bruce Markwardt

I have had a corded Makita angle drill for about 30 years. I have dropped it on the floor at least 100 times. The only issue I have had with it is the little plastic strap that holds the chuck key broke about a year ago. Probably the best tool I have ever bought.

Re: Need a new drill

#17

Re: Need a new drill *LINK*

Juergen

Looks exactly like the $39.95 Harbor Freight Angle Drill. See link.


HF Angle Drill

Re: Need a new drill

#18

Re: Becareful Blowing Out The Dust

Phillip Medghalchi

Stuart, I am hoping that wasn't the reason which sent my Millwakee to the land of the dead. when I opened it up the back ball bearing was blown out and the balls were all over the place, which caused the power gears to get chewed out. Mine went Kapok and no parts available for it anymore.

Re: Need a new drill

#19

Re: Becareful Blowing Out The Dust

Phillip Medghalchi

John, which DeWalt drill is that? I haven't put my Klutch drill to use yet and still am skeptical about using it thinking that it may not hold up under the operation we put them to. I like to know which one is ti that you bought, so I may consider buying it. I just hate the hassle of taking it back and trying to convince them of the poor quality to take it back. I have had lots of good luck with my cordless DeWalts, but I tried to use them as sander, and they run the battery down quickly.

Re: Need a new drill

#20

Dewalt DW106

John Lucas

The newer one has a different chuck that seems to hold the bits better when using it for drilling but for sanding it works the same. They have keyless chucks.

A quick note. hand held drills are not designed for continuous use like we do in sanding turnings. That's why they wear out so fast. Or at least one of the reasons anyway. Obviously sanding dust is a problem.

The normal drill angle isn't the best. I would prefer an angled drill like the Millwauki but I've learned to use both hands on this drill and it gives me much better control. The downside is sanding natural edge bowls which I normally do with the lathe off. Power sanding natural edge it's too easy to round over the lead edge. I have developed a couple of ways to lock the spindle so can use both hands when sanding these bowls or when sanding problem areas on other bowls. That way it's easy to sand and use both hands to control the drill and I can instantly change the position of the bowl to allow access to the area I need to work on.

An I say I developed but in actuallity it's modifications of technques I've learned from this and other forums. I did install indexing on my lathe which works most of the time.