Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Bug help

Posts

Bug help

#1

Bug help

Jim H

I am mainly a lurker here (sounds kind of creepy) but I have learned so much from the collective wisdom of the group.

Any ideas on what this guy is? That pencil has a 0.7mm lead.

I had to move some of my wood stash and found quite a bit of fine powdery dust, some in little piles. Also found thousands of little holes in a significant portion of the stash ranging from about 1/32” to 1/16”. They seem to prefer the sapwood. They don’t seem to like the Ash, or Elm, or any of the Kiln dried stuff.

I moved anything that showed any holes outside. Some of it I would like to save. Any ideas, or advice?

Re: Bug help

#2

Re: Bug help

Barry Irby

Nice picture. I have no idea what the actual bug looks like, but the holes sound like those left by Powder Post Beetles. they live inside the wood and the holes are their exit holes. They are moving to the next location.

They live inside the lumber and must get everything they need from the wood, Including water. If the wood is dry enough, they find it unpalatable. Thus they don't like KD wood that is still dry. Also, heat will kill them. If you raise the temp above about 135 degrees F they die, so the kiln process killed off any that may have been inside. This is true of any insects that may be in the wood, so its generally a good idea.

There are numerous ways to raise the temp. There are also chemicals that will do it, but I am getting more and more skeptical of wood soaked with even "harmless" chemicals.

If you kill the insects, thee wood can be quite attractive, if its not too damaged, and if you like that sort of thing.

Re: Bug help

#3

Re: Bugs

Mark Mandell - Gone Round In New Jersey

Powder Post Beetle (almost positive)

Only sure way to kill'em all is the raise the core of the wood to 180°. Meanwhile get the infested boards out of your stash to protect the remaining sound wood.

If you don't have an oven (kiln) big enough to handle your problem wood, you can try a combination of CO-2 and solar heat. Get some black vizqueen or other 6mil black plastic sheeting. In a sunny location, wrap your boards in the sheeting with 1/4" stickers between them and seal the wrap with tape getting as much of the air out as you can. Before you tape seal the last end put several pounds of dry ice in your "bag" then seal and forget about it for 4-5 days. Very good chance that all your bugs will be dead either from the heat or from the positive pressure of the CO2 (or both.)

Re: Bug help

#4

180 is too high

Dick Coers

135 to 140 is the standard. They do a lot of damage that is unseen until you plane it. It will be covered with channels.

Re: Bug help

#5

Re: Bug help

John Lucas

Put it in a bag with moth balls. It will kill the bugs and not hurt the wood.

Re: Bug help

#6

Chuck Jones - West TN

Re: Bug help  *LINK*


Here is a good article on ppb

Re: Bug help

#7

I Could Be Mistaken

Mark Mandell - Gone Round In New Jersey

But its been told to me several times that while 140° will get the beetles, higher temps are needed to kill their eggs in the galleries.

Re: Bug help

#8

Re: Bug help

Jim H

Once again, the group comes to the rescue.

The pic btw was taken with a iPone5s through a $1 store magnifying glass.

All of the wood that showed any signs is sitting in the driveway. I tossed what was not (in my opinion) worth saving. I’m going to solarize what’s left in black plastic Rubbermaid’s, maybe with some dry ice or mothballs.

I think it will continue to live in them outside on the soon to be constructed wood rack and inspected again before use.

Thanks for everyone’s help.

Re: Bug help

#9

Re: I Could Be Mistaken

r payne

There is a time factor as well as a temperature factor. The longer you can maintain a temperature, the lower the temperature needs to be. A few minutes may be enough at 180 while it may take an hour or more at 140.

Re: Bug help

#10

Jim Barbour

Re: Bug help *LINK*

Jim Barbour

To the original question of what is it, it is a powder post beetle. See the pic and the link - I know, more than you wanted, but I'm an academic and think you simply cannot know too much about anything!

:b


img

http://www2.ca.uky.edu/entomology/entfacts/ef616.asp