Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Disaster Barely Avoided

Posts

Disaster Barely Avoided

#1

Disaster Barely Avoided

Stuart Johnson

Yesterday I was trying to fix an outside faucet. It was a little hard to unscrew but after some extended slow pressure it started to turn. After a bit it was seemed to be unscrewed when I pulled it out I found I had not unscrewed the fitting. I had twisted the copper pipe right in half. This lead to opening the wall (utility room so not bad) only to find the interior pipes had been twisted and bent in order to make up for a three inch offset. Off to the local hardware store only to find out they were out of 1/2 inch couplers so I had to make an 20 mile round trip to the borg.

A semi disaster happened when I was sweating the fittings. Somehow I caught the layer between the brick and frame on fire. A squirt from the fire extinguisher and all appeared well. I turned on the water and had a major leak so I decided to just cap and tackle it today.

After dinner I was just getting ready to sign into the chat room when my wife told me she still smelled smoke and did I think it was just left over smell. I went to check and could not see any smoke or embers but part of the backing did feel hot. I poked around an broke off a piece and sure enough it was smoldering on the inside even though the outside was wet. I was able to set down everything and then cut several inch out back away from the hot spot.

I hate to think what might have happened if she hadn't notice the smoke smell. Needless to say I didn't make the chat session and neither of us got a lot of sleep because of checking on it every so often.

The plumbing part of the job is now finished after I used Shark Bite connections. No more soldering in walls for me.

Re: Disaster Barely Avoided

#2

Re: Disaster Barely Avoided

Blondterror

somehow the small project morph into huge headaches... glad all is well now

Re: Disaster Barely Avoided

#3

Re: Disaster Barely Avoided

Dan Bailey

Go to your store and buy "Sharkbites" Expensive but cheap in the long run.

Re: Disaster Barely Avoided

#4

Dick Hines

Re: Disaster Barely Avoided

Dick Hines

Stuart.Don't you know that a little gob always takes longer than you think. It's that "what can will go wrong" thing.

On the next pipe job go to one of the box stores and get one of the heat resistant. They will glow when heat is is applied but will keep the wood from burning.

They look like the gray scotch bright pads.

Glad nothing bad happened.

Re: Disaster Barely Avoided

#5

many...

GaryG in MD

MAJOR fires occur in buildings being renovated, by workmen with torches. ...GG

Re: Disaster Barely Avoided

#6

Re: Disaster Barely Avoided

Bernie Rose

Two questions:

1) Dick, heat resistant What ?

2) Someone please explain "Sharkbite".

My plumbing has been confined to replacing all the grey Plastic supply lines to my sinks. I have had TWO floodings of my well finished basement in the last month. My insurance co. has not yet told me to go elsewhere, but I am waiting.

Re: Disaster Barely Avoided

#7

Re: Disaster Barely Avoided

jeff Willaford

Heat resistant woven ceramic pad to protect from the flame of soldering.

Sharkbite. A different type of plumbing fitting claiming Cut, push, done with no soldering. Google can be your friend.

Re: Disaster Barely Avoided

#8

Chuck Jones - West TN

Only thing better than Sharkbites is...

Chuck Jones - West TN

...replacing that danged copper with cpvc.

Stuart, glad you got lucky on that one. That's scary!

We built the house that we now occupy permanently as a weekend/vacation project thirty odd years ago. I never excelled in sweating copper joints and scorched a few studs in the process. During last remodeling we replaced 99% of the copper with cpvc. We live in a remote area and there is a constant battle with low pH. In the earlier years before I got that solved the acid destroyed quite a bit of the plumbing and fixtures.

Re: Disaster Barely Avoided

#9

Re: Disaster Barely Avoided

Stuart Johnson

I'm use to small jobs growing or morphing into major headaches but this is the first one that might have taken more than a shot or two of JD to get over. FWIW, I was using a heat shield and don't know where I went wrong. The snakebites worked great but the faucet isn't as secure as the old one. I need to address that problem but at least for now I have water back.

Re: Disaster Barely Avoided

#10

Re: Only thing better than Sharkbites is...

Dan Bailey

"sharkbites" work on CPVC also

Re: Disaster Barely Avoided

#11

Re: Disaster Barely Avoided

phillip Medghalchi

Stuart, first of all I am glad you are safe and so is the family. If you live in USA, your local plumbing or hardware store should have given you this gel spray for plumbing which is used when you have to use any sweat soldering around an area which may catch on fire. It's like the slime from Ghost Busters and goes on any thing that would be around fire area and gives it coating of slime so it won't catch on fire.

Secondly, that problem you had with the twisted copper pipe seems to be common, since they call themselves (plumbers) pros, because their attitude is that as long as I can get the job done and get out of there and get paid, I am OK (and they say if I don't live there I am not going to worry about it. It's not my house). So, having said that now you know what you are dealing with. Shark bites are good products, however, they are subject to turning round and round in their own perimeter. I have used them under my kitchen sink and the problem is that you can not have them hold in a 90 Deg. turn or straight where you want them too.

The main thing to remember next time you go trying to repair something is that originally it was installed with no other obstacles in the way, in your case, it was a bare wall and guy did not have to tackle the problem of the sheet rocks or any other things in his way. So, next time you have to think about how to maneuver around those before you start the repair.

The other thing that you may want to do, is now that you are at it put a safety shot off valve on all your fixture before water gets to the fixtures so when next accident happens then you can shot off the water supplied only to that fixture and not interrupt the water to the rest of the house, so if you get home and you see the accident, but you are tired to attend to it you can cut off the water and get your rest then come back to it to repair when you are well rested with a clearer mind. For instance before I had the major leak in my master bath room I did not have any shot off safety valve to cut the water to the shower, so I had to cut the water off to the whole house and that interrupted the normal routine of showering and cooking, bathroom using (major thing with old folks), etc. Now, that I am getting older as the commercial says (in Cialis pills)(he knows things or two) as I am getting older I am getting smarter. So, I installed a shot off valve to the showers and under neath each faucets in the bathrooms and the kitchen so when a leak happens I shot that particular faucet for that day or the night and get back to fixing it next day when no one is at home, so life goes on smoothly in my house hold.

Good lock with your plumbing fix.

Re: Disaster Barely Avoided

#12

Re: Disaster Barely Avoided

Barry Irby

This is why I like WoodCentral. I have learned a few things in this post. I did not know about the gel product to coat the surrounding area. Thanks to the poster for that info. I also did not know about the ceramic pads. Will try those also. I have always used a layer or two of aluminum foil. It reflects the heat well.

Sharkbites are at one borg and Gatorbites are at the other. They appear to be very similar if not identical. There are tow versions. One can be removed ad reused, the other can not. I have used them many times over the last few years with essentially 100% success. Very expensive compared to solder fittings or CPVC, but very fast and safe in that no heat is involved. An advantage of These fittings over CPVC is that they are instantaneous. There should be a wait time for the glue before turning the water back on. Read the label, but it sticks in my mind that it is a half hour, but maybe much longer, like over night.

For about the last thirty or forty years shut valves or stops have been required for each fixture. The old guard plumber that used to work for me when I was a builder thought they were a joke. His premise was by the time you need them they won't work any more. Now that I am remodeling houses I see that he is often right. Many times we have to start the repair by replacing the stops.

One more thing. Someone mentioned replacing gray riser or supply lines to their fixtures. They may be made of PB or Polybutylene. PB was a major disaster as a material and a lot of it is still around. Use the braided lines instead.

Re: Disaster Barely Avoided

#13

Re: many...

Barry Irby

On many commercial jobs they require leaving a "fire Guard" on the premises if the plumbers use a torch. Some of them use some technology that allows connecting copper with out torches.

Re: Disaster Barely Avoided

#14

whenever...

GaryG in MD

I have to have plumbers in my house, I stand behind them with a fire extinguisher. They don't necessarily like it, but I think they get the point. ...GG

Re: Disaster Barely Avoided

#15

Re: Only thing better than Sharkbites is...

Stuart Johnson

Using them for the outside faucet required anchoring the faucet so it didn't spin in the sharkbite. The problem was solved by mounting a plate to the wall and then attaching the faucet to the plate.