Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Keep shirt tail in

Posts

Keep shirt tail in

#1

Keep shirt tail in

Dick Hnes

I was sanding a bowl that I had coated with sanding sealer. My sanding disk got gumed up so I was cleaning it with one if those spungy things. A loose shirt tail and a disk sander on get along. The disk got wrapped in my shirt tail. It stoped the drill. I was lucky and did not sand my tummy. I now keep my shirt tucked in from mow on

Re: Keep shirt tail in

#2

that's a good warning

GaryG in MD

The lathe wouldn't have been as forgiving!

Thanks for the reminder! ...GG

Re: Keep shirt tail in

#3

Re: Keep shirt tail in

robo hippy

I thought that only happened in 3 Stooges movies! Okay, maybe the Keystone Cops. The shirt usually gets totally ripped off.

Seriously, keep running tools away from everything.

robo hippy

Re: Keep shirt tail in

#4

Joe Fleming

Re: Keep shirt tail in

Joe Fleming

Tim Allen on an episode of "Home Improvement" was demonstrating turning on "ToolTime". Tim turned his back to the lathe and the lathe grabbed his shirt and ripped it right off him.

Re: Keep shirt tail in

#5

Jim Barbour

Re: Keep shirt tail in

Jim Barbour

When I was a kid my dad turned away from a running drill press and it grabbed his t-shirt. The shirt ended up spinning on the chuck, except for the knit ring around the neck which dad was still wearing. I was impressed!

I still have that same drill press in my shop, and it has a foot treadle that must be held down to keep the drill turning. It has been there since the afternoon following the shirt incident!

Re: Keep shirt tail in

#6

I learned a lesson while running......

JamieDonaldson

... a Foredom hand-piece while covering my lap with a towel to catch the shavings. The bit caught in the towel and wrapped in a flash, and cost me a new cable for the Foredom. >(

Re: Keep shirt tail in

#7

Dick Hines

Re: I learned a lesson while running......

Dick Hines

I was lucky. There was not damage to me but my Harley shirt now has a hole in it. >(

Re: Keep shirt tail in

#8

Frightening & very hazardous

Geoff Whaling

Several years back I was the Saturday afternoon workshop convenor for our club & had a new middle aged female turner carry on a bowl project from the morning session. I believe she had done the clubs basic beginners course. The morning convenor had started her off & she was keen to keep going with her bowl on a Vicmarc VL200 but had to wait for me to open the arvo session.

Immediately I noticed her heavy weave synthetic fibre shirt was not tucked in, loose mid length hair, plus the quite dry 12” plus bowl blank which had been quite roughly trimmed & that she was obviously having issues with roughing it down. Lathe speed was way too high & the club tool she was using was blunt & not a good profile – at least it wasn’t an SRG. We changed the speed down two pulleys while I explained a few safety matters & said please tuck in your shirt, see if you can put your hair up with your cap while I duck out & grab my tools. Don’t do anything until I get back.

Basically I got back the firm response that the “morning convenor set it up that way & didn’t have a problem with me turning like this so why do you want me change”. I explained a little more about safety. Then as I went out to my vehicle to bring in my tools to help her out she grabbed the blunt bowl gouge & decided to have another go.

I had only gone a few paces when I heard a bit of a yelp & raced back in to find her loose shirt tail had been drawn in and caught up in the slower spinning bowl blank & was dragging her in towards the very rough edges of the bowl blank. Thankfully she was a fairly robust woman and had the reflexes to drop the gouge and get her hands against the lathe to resist it pull. I managed to kill the lathe power but she was now basically wearing an apron instead of a shirt which exposed a substantial area of her bra on her LHS, did not have any injury but her pride took a huge hit.

She went off home on the pretext to get a new shirt & that was the last the club ever saw of a new member. I still believe that had I not turned the lathe speed down it would have resulted in a very severe injury, that it should never have happened in any case & just how much modesty, pride & saving face makes us all do dumb things at times.

Re: Keep shirt tail in

#9

Re: Frightening & very hazardous

Dennis Bilevich

And what about the long tails on the smocks?

Re: Keep shirt tail in

#10

Re: Frightening & very hazardous

Geoff Whaling

Close fitting is the key.

We choose to hand turn. That means we deliberately choose to overlook the elimination & substitution solutions (machine guards with interlocks & semi automated turning processes) which will remove us from the hazard.

So we apply administrative and some engineered solutions to remove some but not all of the risk.

Re: Keep shirt tail in

#11

Re: I learned a lesson while running......

robo hippy

Dick, I am having a difficult time figuring this out. How did you get holes in your Harley shirt while running??? Dog? Fall under a street sweeper?

robo hippy

Re: Keep shirt tail in

#12

Learned that lesson in Gr 9 welding class ...


Re: Keep shirt tail in

#13

Jerry Louden

Re: Keep shirt tail in

Jerry Louden

Besides keeping your shirt tail tucked in for safety, doing so also helps keep your pants up.

Re: Keep shirt tail in

#14

Re: I learned a lesson while running......

Dick Hnes

I was cleaning s sanding disk with one of those gummy thingies and the disk got cought in my shirt.

Re: Keep shirt tail in

#15

Roger in MO

Re: Keep shirt tail in

Roger in Mo

This reminds me of the lathe safety poster from about 1950 which showed the student nearly strangled by his neck tie which was wrapped around the spindle of a lathe.

Re: Keep shirt tail in

#16

Re: I learned a lesson while running......

robo hippy

Now I get it, I live in a running town, so was thinking of that type of running.....

robo hippy