Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

moving a 300lb compressor

Posts

moving a 300lb compressor

#1

moving a 300lb compressor

John Lucas

Got it installed yesterday. A little over a year ago I purchased a 60 gallon dual stage compressor. It's been sitting on my back porch all that time waiting for me to put in new 220 lines. Well moving the beast became a problem since I hurt my back a week ago so I had to use the old noggin to come up with a solution.

Yea I know calling friends and drinking beer came to mind but we all live pretty far apart and I don't drink beer so the hermit in me had to come up with a better idea.

I used a home made block and tackle to lay it down on a dolly. rolled that across the porch to some ramps that go to my trailer. Used the same block and tackle to roll it down the ramp to the trailer. I parked the lawn mower on the trailer tongue to keep the down hill slope of the trailer. Tied off the compressor at the balance point of the trailer. Hooked the trailer up to the lawn mower and drove it around to the shop. Hooked up the Block and tackle and then tilted the trailer so the compressor would slide. When there was enough weight I let the trailer tilt up as much as it would. Propped a board under it so it wouldn't come back down.

The compressor is very top heavy. I let is slide down some more until one side was on the ground. Then I hooked up another sort of block and tackle (made from climbing rope and carabiners). this one was attached to the back wall of the shop using my old climbing rope. I pulled the compressor into the upright position while holding the original block and tackle to keep it from rocking too far and set it upright. Then tilted it very slightly left and right and walked it into place.

I still have to pick it up and put it on the rolling base I'm building because where it sits it's in the way of getting my lawn tools. I'll use the chain hoist and a homemade A frame to lift it when I get ready to put it on the rollers.

Had to pat myself on the back for this one. Use your brain and not your back when you get my age. My neighbor who is getting over a very serious back problem came over and said I would have helped and I know he would but I didn't want to ask.

Still need one more plumbing adaptor to get it working but it runs and more or less fits where i needed to put it. Been without a compressor for 2 weeks now. It's one of those things that you don't miss when you don't have one but after you do you realize how much you do use it.

Re: moving a 300lb compressor

#2

Re: moving a 300lb compressor

Phil Powell

John,

I'm not that far away from you. So, if you ever need one more aching back I'm available.

Phil

Re: moving a 300lb compressor

#3

Re: moving a 300lb compressor

John Lucas

Phil seems like all my friends have aching something or another. My good friend who lives nearby and gives me hand when I need it now has a bad shoulder and getting over rotator cuff surgery. I know he would have helped but don't want to ask if I don't have to. He doesn't need any more aches and pains either. Maybe you could come over and we could sit and drink something and just talk about moving things. :)

Re: moving a 300lb compressor

#4

Lyle Jamieson

Re: moving a 300lb compressor

Lyle Jamieson

While you are at it put a drain valve and pet cock with an elbow and tubing so it is accessible from the side of the compressor where you can get a collection drain pan under it. Its a pain to lay on the floor and reach under it just to drain the condensation water.

Re: moving a 300lb compressor

#5

I'll just do some push ups

John Lucas

No reason to waste crawling on the floor. Actually I did that on my last compressor and will do it on this one as well. Since it's close to the door and going to be on rollers I'm going to make the drain pipe long enough to reach out flush with the side of the compressor so I can role it over near the door and drain it.

Re: moving a 300lb compressor

#6

Your solution was better than mine....

Barry Irby

I hitched mine to my cat. At first he couldn't move it. Had to use the whip. Not sure where he went after I unhitched him. Its been about a year and I have not seen him.

Re: moving a 300lb compressor

#7

Ric Taylor

Re: moving a 300lb compressor

Ric Taylor

There was a person in my club who had a REALLY heavy compressor. That person didn't know about draining water out of the bottom. Now that compressor isn't nearly as heavy as it used to be.

Re: moving a 300lb compressor

#8

Re: moving a 300lb compressor

Jerry Klug

Remember to drain the condensed liquid frequently. During humid weather a compressor should be drained daily. For your planned compressor location add a chain to secure it from falling over, espically since it will be on rollers. There is always a chance of something falling against it and moving it when you don't want that. Also there is a chance of an earthquake, maybe not a large chance in your area but they do happen in some unexpected areas. Better to be safe and a simple length of chain will secure it. If this is your first two stage, you will enjoy the quieter operation.

Re: moving a 300lb compressor

#9

Re: moving a 300lb compressor

John Lucas

Well the New Madrid Fault is overdue. However if it is a large as it was when it formed real foot lake a falling compressor will be the least of my worries. :)

Re: moving a 300lb compressor

#10

Re: moving a 300lb compressor

Sergio

I would say use your brain and not your back at any age!

Give me a solid point and a lever and I'll lift the Earth said Archimedes.

Re: moving a 300lb compressor

#11

Steven Antonucci

Egyptians built pyramids.

steven antonucci

Simple machines are effective. Simple is good and often the answer.

I was looking at large I-R compressors the other day. For the life of me, I don't understand why they don't have wheels?

Steve

Re: moving a 300lb compressor

#12

Chuck Jones - West TN

Too top heavy for wheels

Chuck Jones - West TN

"I don't understand why they don't have wheels?"

Probably because, as John said, they are too top heavy. Several years ago mine tipped over and off a pallet as I slowly inched it down an incline with a front loader. Next time I tied it down better.

Re: moving a 300lb compressor

#13

Re: Too top heavy for wheels

John Lucas

When I moved to this shop I moved every bit of furniture and tools by myself. The only thing that nearly hurt me was the drill press. It's surprisingly top heavy and got away from me. I was barely able to hold it but really stressed my back. This big air compressor is the same or maybe even more so. I am going to put wheels on it but you can bet that I will move it very slowly when I need to.