Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Running lathe electronics off generator power

Posts

Running lathe electronics off generator power

#1

Running lathe electronics off generator power

Roger Chandler

Does anyone know if it would damage the inverter on a lathe if it was run off portable generator power? I have 2 lathes........my full size has 2 hp and my midi has 1 hp motors with inverters respectively.

Re: Running lathe electronics off generator power

#2

Dick Hines

Re: Running lathe electronics off generator power

Dick Hines

Not sure I would do that. The generator may not keep a level voltage.If/when we loose power I don't run my PM.

Re: Running lathe electronics off generator power

#3

Alan Zenreich

Re: Running lathe electronics off generator power

Alan Zenreich

It depends on the generator type. I have two Honda -inverter- generators, they can run the most sensitive electronics because their inverter does the voltage conversion and regulation. I don't think I would trust most contractor style, conventional generators with any sensitive electronics.

Re: Running lathe electronics off generator power

#4

Re: Running lathe electronics off generator power

walta

No one can answer your question with any certainty.

1 Will you damage your generator? Not likely.

2 Will you damage your lathes electronics? Maybe or maybe not it all depends on how the circuits were designed. It may run for some time until the generator has a hiccup and then blow up.

3 Will your lathes run on the generator? My guess is yes the small one will and no the big one will not. I suspect the variable frequency drive in the larger lathe will detect the input power is not exactly 60 hertz and shut down with an error code. Maybe its parameters can be adjusted if the manufacture allows you access.

Walta

Re: Running lathe electronics off generator power

#5

Chuck Jones - West TN

During power outages I have higher priorities.

Chuck Jones - West TN

Roger that sure is an interesting academic question, but during the rare power outages we have here on our farm I am too busy with other emergencies to even think about running a lathe.

Re: Running lathe electronics off generator power

#6

Re: During power outages I have higher priorities.

Ralph Lindberg

I largely agree with Chuck, although we get power outages so regularly that, well, few homes around here don't have generators of one sort or another (it's actually been two winters with no multi-day long outages, first time we've gone two years in the entire 35 years I've lived here)

As I noted on Sawmill creek, the inverter-generator style is really solid system (I have two Honda 2000s)

Conventional generators generate power almost exactly the same way your power-company does.

Conventional generators are very noisy, as they are designed to run full out, all the time, to regulate their frequency.

Conventional generators are fine for electronics, Hams have been using them for decades to power their radios for certain types of contests and exercises.

Re: Running lathe electronics off generator power

#7

Re: Running lathe electronics off generator power

Dale Miner

I have ran my 3520B on the power from my 5KW Honda generator. It is not an inverter type. I dont use the auto idle function when using the lathe, and do keep a resistance load (filament light bulb)on the generator to help knock down any transients.

I have done this several times over the course of the last few years and have not had any hiccups from the lathe's inverter.

Also, have ran a variable speed Jet mini on the same generator without issue on more than one occasion.

But, your mileage may vary.

Re: Running lathe electronics off generator power

#8

Alan Zenreich

Re: During power outages I have higher priorities.

Alan Zenreich

Ralph, I also have a pair of Honda 2000is generators. They run in parallel and connect to the house through an APC-UTS6 transfer switch. My initial setup used extended run fuel tanks. About a year ago, I did a Tri-fuel conversion on both units... It's a joy to run them from our house's natural gas line. Gasoline, natural gas, or propane... makes for a pretty flexible, and portable setup.

Re: Running lathe electronics off generator power

#9

Re: Running lathe electronics off generator power

Roger Chandler

Thanks all! Dale, your experience helps me. If I ever did this, it would be rare, but thought I would ask just in case I got in the middle of a project on the lathe and the power from the utility went out and needed to finish up the project.

I am going to have a licensed master electrician set up a transfer box to the house which will have 16 circuits and will supply back up power to essentials. The generator I am getting is 8000 running watts and 10000 starting watts. A generac with pressurized lubrication and industrial engine.

Re: Running lathe electronics off generator power

#10

Re: Running lathe electronics off generator power

john Veerkamp

The Generac's I'm familiar with have conditioned power to prevent damage to the sensitive electronics on modern heating systems and refrigerators. Your lathe's should be fine if your generator will accommodate modern households.

Re: Running lathe electronics off generator power

#11

Alan Zenreich

Re: Running lathe electronics off generator power

Alan Zenreich

Also consider the fuel consumption rate of the generator.

Conventional generators run at full speed when any load is present.

During hurricane Sandy, I saw lots of people buy generators, but not nearly enough fuel for an extended outage. Then there was little or no fuel to be had during the outage because the gas stations had no power.

So, consider tri-fuel conversions that give you the option of alternate fuel sources.

My approach with generators was not to power the entire house, but instead, 6 important circuits, at high fuel efficiency. The thought is that in an emergency, I need/want a lifeboat, not an cruise ship

Re: Running lathe electronics off generator power

#12

Brad Vietje

Re: Running lathe electronics off generator power

Brad Vietje

I'm completely with Alan on this.

Since I'm in the solar business, and in the sticks of Northern VT, I have lots of customers with off-grid homes and generators to back up their solar panels in winter when we don't get much sun.

Most of the common work-a-day generators from the big boxes put out very unstable and noisy power. They would be OK for a simple capacitor-start single-speed motor, but don't try to run a variable speed lathe (that you like) off these units.

Honda makes some of the nicest inverter generators out there, and they will work with any lathe within their power capacity. Most of the good quality generators that put out clean power are not the sort you'd travel with -- except the little Honda EU series, which are sweet.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Running lathe electronics off generator power

#13

Brad Vietje

Here Here!  Well Said.