Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Lathe question.....

Posts

Lathe question.....

#1

Lathe question.....

Barry Irby

I made a mistake setting up my lathe. I built a cabinet that has six drawers Under the ways. the top if a piece of oak butcher block I made myself. The is a box/shaft under the head stock that is filled with sand. (about 330lbs, IIRC.) And there is sand in a tray under the butcher block and in the toe kick. All of this is under Nova DVR. the shaft is about at elbow height.

The problem is that I mounted the lathe directly on the oak top. The is only about a 1/2 to 3/4" clearance under the ways. Chips and crud accumulate under and between the ways and its a PITA to get them out. Not really all that hard, but a constant irritation. The plate that holds the tails stock onto the ways does not have much clearance and it tries to shear off stuff and it slides along and it bangs to a stop. Its a tight squeeze to try to remove them from under the ways and tough to get it out the top, even with the dust collector in the shop vac mode.

So, having said way too much, What difference would it make if I placed spacers under the lathe and raise it 3/4 or 1"? Will that be uncomfortable to have it above the elbow height? As an aside, I get some back pain and particularly a snarled muscle in my right shoulder.

Re: Lathe question.....

#2

Re: Lathe question.....

Don A. Davis

Barry, I have my 3520B raised about 2 inches above my elbow and love it. I stand straighter and am more comfortable. Therefore, can turn for longer periods. I wouldn't hesitate to give it a try.

Re: Lathe question.....

#3

Re: Lathe question.....

John Lucas

Barry I like my lathe about an inch above elbow height. It keeps my back straighter and reduces strain. The good thing is, you can always remove the spacers if you don't like them. Just don't glue them down.

Re: Lathe question.....

#4

spacers

Jeff Willaford

As Don and John have said.... raise it. I had space under my DVR to clear shavings and still raised it for comfort. I've always heard the elbow height was a place to start....not a true requirement. Try it. You might like it.

Re: Lathe question.....

#5

Re: spacers

Jim Pugh

You can always drop a sheet of 3/4 plywood on the floor to get you back to the same level.

Re: Lathe question.....

#6

The "correct" lathe height is that.......

JamieDonaldson

...which best suits your physical turning requirements, and your back is usually the first indicator of what height is not best for you. Many turners who hollow raise their lathes several inches higher than bowl turners, so experiment until your body says OK! ;)

Re: Lathe question.....

#7

blow the chips out.

Darryl

I have my XP mounted on the old Teknatool stand. when I finish for the day the last thing I do is use my blow gun to empty the spaces. In particular the space under the headstock. Stuff come right out with about 50# pressure

Re: Lathe question.....

#8

Ellis Walentine

What part of the lathe are we talking about?


Re: Lathe question.....

#9

The whole thing/ mostly the bed/ways

Barry Irby

The lathe is mounted on a flat surface so shavings accumulate. Because the bed is low tot he surface, there is not much of a crack under it let the shavings out and its a PITA to get them out. What makes it a problem that can't be ignored is the plate that holds the tail stock on hits them against the cross ribs. I am not a neat freak As any picture of my shop would reveal, so I got no problem with a few shavings, or a lot of shavings, but it is astonishing how little it takes in the right place to crash the headstock to a halt. The long stringy shavings off bowls in particular are hard to get out. I figure another of inch of clearance between the bed and the surface will really help, but I did not want to mess with the height if it was going to cause other problems.

Re: Lathe question.....

#10

Re: blow the chips out.

Barry Irby

Daryl, I snort them out with the dust collector hose, rake them out, and pick them out and occasionally blow the out. Blowing them out is something of an explosion. Bowl turning on green wood seems to be the biggest problem. The long stringy shavings (think three 45 gallon bags of hem in four days) are really difficult. They don't snort or blow well. They hang on for dear life. I have been turning green to finish and have a nice mix of shavings down to dust. I use the dust collector for the sanding, but it does not do much for the actual turning. If this were and end of the day problem I would be fine, but it takes about ten minutes for it to clog up again.

Re: Lathe question.....

#11

Re: blow the chips out.

Pete in Holland, MI

I'm 6'0" tall. Spindle on my Jet 1642 is a couple inches above the horizontal plane of my arm, and works fine.

Space your lathe up. Make spacers such that they support the total foot area of the lathe and you'll be fine.

Pete

Re: Lathe question.....

#12

Re: Lathe question.....

Chuck Engstrom

Hi Barry -- I have a 3520 and often slide my headstock down to the right-hand end to do the inside of bowls, HFs, etc. I sometimes felt I was bending over too much for this, so I tried jacking up that end of the lathe with a cheapo hydraulic bottle jack from HF, pushing a pair of matching riser blocks under the raised feet, then releasing the jack to let the feet settle down on the blocks for a solid stance. I only raised it about 1-1/2 in. and found that more comfortable.

All this can be undone quickly to return the whole lathe to level, and I never found that having the end cocked up at a very slight angle made any difference at all in the actual turning.

Best -- Chuck

Re: Lathe question.....

#13

Re: Lathe question.....

Dick Hnes

Barry, there is no right height for a lathe. It all depends on the users needs. I bet my lathe would be unuseable for most turners on this page. My spindle is a little over 50 inches high. It works because of my height and my style of turning.

Re: Lathe question.....

#14

Brad Vietje

Back Pain

Brad Vietje

Barry,

Lots of people get back pain from low spindle heights or from reaching over the bed to hollow out bowls. If you have the space, another option to help prevent reaching/leaning over is to stand on the other side of the lathe, if you can't turn the headstock, or slide the headstock down and stand off the end of the ways.

For turning bowls and hollow forms, standing on the "wrong" side of the lathe can help a lot.

Safe spinning,

Brad Vietje

Newbury, VT