Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Like riding a bicycle-sorta

Posts

Like riding a bicycle-sorta

#1

Like riding a bicycle-sorta

John Lucas

Well I'm getting ready to go for a 24 mile ride. Need a break from turning ornaments plus need to burn off some calories. I turned 10 ornament balls between last night and this morning. The tenth one finally felt good, hollowed rapidly to an even 1/8" wall thickess. The first 9 were OK but the walls weren't quite even.

The Blue ones are cast resin blanks I got from George Taylor who got them from Alan trout. they are Acorn caps in blue resin. Pretty cool. Hollows kind of difficult. It grabbed my normal hollowing tools but the custom made Hunter tool I use works great except for the fact that it tends to cut curls instead of chips. These clog up the ball really rapidly so I had to stop after each pass and blow them out.

I'll start on the finials after my bike ride and dinner.

Re: Like riding a bicycle-sorta

#2

Dan Jechura

Re: Like riding a bicycle-sorta

Dan Jechura

wish I could do something like this. Someday I will make the time to learn.

Re: Like riding a bicycle-sorta

#3

It's just patience

John Lucas

Take it slow and you can do almost anything turning wise. I look back at some of the projects I did 20 years ago and wonder how I had the skills to do them. But then I think about it and realize I probably used different tools and used them differently. It went a lot slower and I probably sanded a lot more but I got it done. That's what it's all about. Just make whats in your mind. don't worry about how you get there.

Re: Like riding a bicycle-sorta

#4

George Taylor

Re: Like riding a bicycle-sorta

George Taylor

The acrylic blank actually came from Eugenio Soto of Amalgum Mutts; he and Alan "conspire" together here in San Antonio. They both go through a lot of resin. ;)

Looks good no matter what John; can't wait to see the final ornaments.

Re: Like riding a bicycle-sorta

#5

Re: Like riding a bicycle-sorta

Mavdad55

John, very nice. The only ornaments I have turned are the small bird houses via the late Dale Nishs book. They turned out nice, due to Dales instructions; but they typically have a large 5/8 or so hole to hollow in. Is your Hunter tool on a 3/8 shaft? I assume it has enough bend in it to get behind the neck? Or are you using multiple tools?

Re: Like riding a bicycle-sorta

#6

Re: Like riding a bicycle-sorta

John Lucas

My homemade Hunter tool was carefully designed from flat stock to be able to reach around corners and hollow most shapes that I do on my 3 part ornaments. I do think I need to change the hook angle slightly and may possibly angle the cutter down more although I got it pretty darn close to right the first time. I may build another one shortly to see if I can over come it's few slight dissadvantages.

I do hollow the entire ornament with it. Normally I use 2 tools. A straight tool made from 1/4" drill rod and one that has a slight bend at the tip. The slightly bent one requires a good grip. I intend to bend a C in it sometime to align the cutter with the shaft to overcome this twisting motion however that requires that you ride the tool on the tool rest at the bottom of the C. On a 1/4" shank that introduces chatter so it needs to be slight.

The Hunter tool I designed gets more stable the deeper you go because the flat surface helps keep the tool from twisting. I can hollow through a 1/2" hole. Wih my 1/4" cutters I can hollow through a smaller hole but it just takes so much more time due to clearing the swarf that it's much faster and easier to open the hole up to about 1/2" One of the tools photographed below has a high speed steel cutter silver soldered to it. This one is really grabby and I don't recommend it but it does allow me to hollow really square bottom ornaments better.




Re: Like riding a bicycle-sorta

#7

Re: Like riding a bicycle-sorta

Mavdad55

John thanks for the pictures of your cutters. I use a Dale Nish scraper that also has a similar flat shaft. Your carbide cutter tool would be nice to use on bird houses and small bowls I like to turn, they have a short turned in rim. I would post pictures but have not figured how to do so with an iPad. Site says pictures are to large and I have not found any photo editors that will resize the pictures.

Re: Like riding a bicycle-sorta

#8

Re: Like riding a bicycle-sorta

Mavdad55

Found a tool to resize my pictures on an iPad. If I resize to 640x480 it is small enough to upload. Hope this works


Re: Like riding a bicycle-sorta

#9

Re: Like riding a bicycle-sorta

Joe shelton

Hey, I use an iPad, too, and would like to be able to resize pics. What is that tool?

Joe

Re: Like riding a bicycle-sorta

#10

Re: Like riding a bicycle-sorta

Dwight Rutherford

Have an iPad also. What app do you use?

Re: Like riding a bicycle-sorta

#11

Re: Like riding a bicycle-sorta

Mavdad55

The iPad app is called SimpleResize

Re: Like riding a bicycle-sorta

#12

Re: Like riding a bicycle-sorta

Dwight Rutherford

Looked for the app "SimpleResize", couldn't find it.

Re: Like riding a bicycle-sorta

#14

Re: Like riding a bicycle-sorta

Dwight Rutherford

Got it. Works like a charm. Thanks