Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

accident

Posts

Re: accident

#26

Thanks! (emailed permission(

mjonesrdg

I'll spell your name correctly in the future. My intention is to post your photos and description of injuries on other wood turning forums. Your willingness to share just might prevent others form suffering the same kind of results that you have experienced.

Re: accident

#27

Re: Marshall - elaborate on "Lexan Bubble Visor"

Geoff Whaling

When selecting a face shield suitable for woodturners we are looking for one that satisfies,

Ability to protect against specific hazards.

Resist penetration by objects.

Absorb the shock of a blow.

It should also

fit properly and be reasonably comfortable to wear.

provide unrestricted vision and movement.

be durable and cleanable.

allow unrestricted functioning of any other required PPE (hearing & respiratory protection).

The hazards – typically are splashes from liquids; impacts from high/low velocity/mass objects; kickbacks from hand held tooling (angle grinder / power carvers & the like) that may cause an eye, face, brow or head injury.

The face shield has three significant components the visor, brow guard & harness.

The visor gains a lot of its strength from the material and from the Hz & Vert curvature in the design. It should add strength, not fail or deform inwards under impact conditions, and should contribute significantly to deflecting a high mass flying object and hence a lot of the impact energy away from the head.

The brow guard retains the visor and attaches it to the head via the harness. The brow guard should function and offer protection in a similar manner to the visor which is what the Trend did to an extent in Aiden's event.

The next component is the harness - the bit that attaches the face shield to our head. The harness like a safety helmet's (hard hat) is designed to fail in a controlled manner to absorb or at least reduce impact energy. The harness is designed to be fitted firmly to the head to position the visor/brow guard in an optimum position, securely retain it in position then progressively fail under impact loads. It must be comfortable enough to be worn for long periods.

It is important to select personal protective equipment that meets the hazard and risk level for the projects undertaken. A splash guard style face shield may meet the above criteria for light spindle turning but would be considered inadequate for the hazards and risk associated with large platter or bowl projects.

Standards associations do a lot of the hard work for us. Look for the standards approval markings/stamps/labels and understand what they mean.

Don’t take head injury lightly – “While about a quarter of people with severe brain injury will make a good recovery, about a third will die, and a fifth will have severe disability or be in a vegetative state.”

Re: accident

#28

Re: Glad you are recovering, and shared this.

robo hippy

Besides standing out of the line of fire and proper head gear, another safety consideration is being able to recognize 'high risk' pieces. The black line at the top of this piece shouts DANGER to me. Add in the bark inclusion in the center, and more DANGER. Any black lines indicate rot to me, even spaulting.

robo hippy

Re: accident

#29

Re: Glad you are recovering, and shared this.

Adrien

You are quite right about the flimsyness of the piece.

The problem, I think, was leaving the lathe at its highest speed when it was turned off, and

not realizing this when it was turned on.

As with beautiful women, high risk, yes, but so attractive. /temp/9679859b6820b053131d6acddb3802c2_3_library353.jpg" />

Re: accident

#30

Re: Glad you are recovering, and shared this.

sergio

yes I agree: an automatic switch that bring to zero speed when you turn off the lathe make a lot of sense. But I'm already hearing the usual tough guys say that there is already too much government inteference, that the cost will go up, that safety is a personal responsability, that they never had an accident etc.

I have a saw stop, I'm rather careful but one day I was tired and said to myself: this is the last cut. And I touched the blade. Fortunately I have a saw stop with too much government interference.

Re: accident

#31

Integrated head and face protection....

Steve Russell

Hello,

I have been using 3M's AS 400LBC PAPR for many years. It offers integrated head and face protection, as well as protection from dusts via it's HE dust filter. It's none to cheap though, which is unfortunate but it is an excellent system if your wallet is thick.

This headgear meets the requirements of ANSI Z87.1-2003 (Eye and Face Protection) and ANSI Z89.1-2003 Type I, Class C (Industrial Head Protection). When I bought my unit several years ago, I paid around $900.00 for the helmut, the battery and a fast charger. Considering the cost of an Emergency Room visit these days, it's not all that expensive.

Steve Russell

President and CEO

LSWA, Inc.


img

Re: accident

#32

Facial hair?...

Jorge

The head is protected as is the face, but a fellow wih a beard like me, will that work for the dust protection part?

Re: accident

#33

Re: Facial hair?...

Steve Russell

Hello,

Yes, it will work with a beard... I turn with a full beard and have no problems using the 3M PAPR. There is a flexible seal that fits under your chin, so using it with a beard easy peasy. The unit pulls in air from the rear of the helmut and pushes it through the HE filter in the top of the helmut.

The exhausted filtered air flows into the top and sides of the helmut and then flows out around your head and face. This creates a positive pressure inside the helmut, which keeps the dust out. Several of my friends also turn with this PAPR with varying styles of facial hair as well. The battery easily lasts for a full eight hours (longer really if you take care of it), so you have plenty of time to get your work done.

If you decide to get one, the fast charger is worth the extra money, as the standard charger is way too sloooooooooow. Cheers bruddah.

Steve

President

LSWA, Inc.

Maui No Ka Oi Bruddah...

Re: accident

#34

Mahalo!

Jorge

Good to know, thank you Steve.

You are right, Maui no ka oi

I lived there in the 70's...