Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Vortex and skewigouge

Posts

Vortex and skewigouge

#1

Vortex and skewigouge

Joe shelton

I've seen 2 tools called Vortex (from SB Tools and another from Cindy Drozda) and Crown's skewigouge, and they appeal to me. Are they useful for fine detail on spindles, such as bird's beaks?

Are they the same basic approach? They look really similar to me. Cindy's video depicts use at the minor diameter of an evanescent finial, and I wonder if they are just for very small stuff.

Thanks.

Joe

Re: Vortex and skewigouge

#2

The skewigouge is one of the ..........

JamieDonaldson

...most useless tools I've ever bought, years ago before I knew better! BTW, what is a bird's beak that you mention?

Re: Vortex and skewigouge

#3

Re: Vortex and skewigouge

John lucas

The vortex to is ground to a sharper angle than the other tool so it is better for reaching into really tight areas. However a thompson deta gouge sharpened to a 35 degree angle will do 99 percent of all you need to do. Its a more. Versatile too o think

Re: Vortex and skewigouge

#4

It is,

Joe shelton

As you'd expect, a compound shape, with a convex rising side (in profile) that devolves into a concave shape that undercuts the convex. A Beaked shape.

Joe

Re: Vortex and skewigouge

#5

Re: Vortex and skewigouge

Joe shelton

Well, I like those Thompson tools. When you say this, which diameter are you suggesting? He offers 1/4, 3/8 and 1/2.

At this point, I can't distinguish between the influence of skill, which I have one of, and tooling, which I can buy.

Joe

Re: Vortex and skewigouge

#6

Re: Vortex and skewigouge

robo hippy

I rate the skewchigouge in the same category as the spindlemaster. They have a 45 degree bevel. Some people can use them, but I can't. I haven't experimented with the vortex tools, but they look long and very pointy. I have one of the small fluteless gouges from Doug that I ground to a spindle/detail gouge profile and love it. First saw it with Allen Batty using it. I do love the Thompson fluteless gouges, and will have a You Tube clip up soon. It isn't a detail gouge though. Finish cut tool. I guess the skewchigouge more resmbles the fluteless gouge, but has a flat ground on the top side so you are really working with a half round bar profile. For detail work, I would grind it to more of a point.

robo hippy

Re: Vortex and skewigouge

#7

Re: Vortex and skewigouge

Bill Jacksonville, NC

Skewchigouge looks like nothing more than a round skew you need a diamond stone to sharpen.

I am confused when it comes to SB or Cindy Drozda Vortex Tool. Know have sharpening instructions on line and need a diamond stone to hone.

After looking at grind library here sharpen an old HSS 3/8” spindle gouge with pointy bevel on my grinder and use as cleanup tool. Watched a turning video where turner did same to turn his finials. He mentions bevel angle where as I have no idea what angle is on my old gouge. Think Ellsworth mentioned a bevel angle too!

Bob Rosand wrote AAW article on making his own ¼” skew many years ago. That is what he uses on his finials. Nice read and might provide less expensive alternative to either Skewchigouge or Vortex Tools

http://www.rrosand.com/articles/19-3a.shtml

Re: Vortex and skewigouge

#8

Re: Vortex and skewigouge

John lucas

I have a 3/8 and 1/2. I use the smaller one for almost everything. Probably my most used tool besides the bowl gouge. If you were going to tie. A lot of really small coves the 1/4" would be better. These will get i to reallu tight areas if sharpen them at 35 degrees. Any tighter than that and i use the toe of mu skew. P

Re: Vortex and skewigouge

#9

Gosh i hate typing on my phone 


Re: Vortex and skewigouge

#10

Re: Agree on the detail gouges

Steve Criscenzo

I agree with John Lucas. Go with the Thompson detail gouges. I have the 1/4 and 3/8 and use them extensively. Great tools for many differeent applications but they really shine for detail work.

Steve

Re: Vortex and skewigouge

#11

Re: Vortex and skewigouge

Paul Singer

Reed,

I am really wanting to see your video on flutless gouges. I have the DT 5/8" and have yet to figure out how to use it.

Paul

Re: Vortex and skewigouge

#12

Re: Vortex and skewigouge

robo hippy

Paul,

I am doing a little reshoot today, and it should be up in a day or two. Most of it is done. I will post it here. No commercial, I just love the tool.

robo hippy

Re: Vortex and skewigouge

#13

Re: Vortex and skewigouge

Paul Singer

Fantastic.

Thanks