Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

First hollow form

Posts

First hollow form

#1

First hollow form

david

When Don Derry first came through the islands doing demos ten years ago, I saw his hollowing system in action and bought one. I was in the mode of being more proficient at making bowls and chasing the Holy Grail that Bill Luce had set. My story was I was a bowl maker and would get around to hollow forms when I grew up. The advent of turning boxes a couple of years ago came close, but those were forms I could use ordinary bowl gouges to make. When Don made a return visit a couple of months ago, I decided to dust off my hollowing rig and signed up for the hands-on session. Even after all those years, the components worked well, with a replacement laser pointer that I re-purposed for use with a slide show at work. I opted to fix the laser at the point of touching wood, rather than re-setting the laser when the angle of approach to the wood changed. The walls were probably 3/16" thick, when I used a scraper attachment to smooth out the cut surfaces. Probably at 1/8" now. Wood is Silky Oak cut through a 7/8" opening, with an added ebony collar narrowing the opening so intruding fingers could not check out the inside finish. Don't think the form is quite there yet, but for a first piece I guess it passes. I found a Hawaiian quilt pattern with a stylized Kukui Nut pattern, and used a stick-n-burn film to trace around the collar. Think the pattern around the top draws your eye upward, helping to de-emphasize what I thought to be an overly bulbous form. When my wife saw the finished piece, she said I can't sell it because she gets all of my first editions. I guess it passed the acid test.


Re: First hollow form

#2

Shot from above

david


Re: First hollow form

#3

So David, are you turning "backwards".....

JamieDonaldson

...as Don does? I made a replacement tool holder for my Derry rig that allows turning in the proper "anti-clockwise" rotation, just as I was accustomed to doing. Don did a demo for the OVWG years ago, and it was a real problem for Don because the Woodfast demo lathe did not reverse! I preferred viewing the laser on the front side rather than the back side of the vessel. That rig has been a wall decoration for about 10+ yrs. because I found better equipment in my Monster, but the elegance of the brass laser adjusting mechanism is very attractive. ;)

Re: First hollow form

#4

Brad Vietje

Fantastic, David!

Brad Vietje

David,

That's a very nice little hollow form for anyone, so if it's your first, so much the more impressive! I don't know what you'd do to improve the form -- from the photo it looks great. I'm sometimes my own worst critic, and sometimes I can feel a little something that no one else can see, but I know that another experienced turner could feel it, so I'm not sometimes a bit too critical. I'll assume your concerns are as subtle as these invisible worries -- it looks splendid.

Keep 'em coming, you're off to a flying start!

Safe spinning,

Brad Vietje

Newbury, VT

Re: First hollow form

#5

Re: So David, are you turning "backwards".....

david

Yes, Jamie, I am turning backwards with this rig. Don said he has never had problems with unwinding the treads going backwards. Perhaps because this rig has a practical limit of about a 9" hollow form, so the wood mass is not that great. The laser setup he has is very simple, robust and steady. As I am over 70, I may now be grown up enough to do more of these.

Re: First hollow form

#6

Steven Antonucci

it's a great first vessel

Steven Antonucci

Only thing I think I see is the major diameter seems a bit too high in the form? Perhaps that's what you mean by bulbous?

Love the pattern, maybe not the collar? The neck with burning the pattern... maybe?

Steve

Re: First hollow form

#7

Bill Blasic

Re: First hollow form

Bill Blasic

David,

Well done!

Bill

Re: First hollow form

#8

Re: First hollow form

Mike Rubes, Cary, NC

Hi David,

Sorry this took me so long to see, I have been away, but this is wonderful! You should be very pleased if this was your 100th hollow form. I love the collar treatment and the finish is fabulous.

Thanks for the pic. I hope all is well in Hawaii.

Mike

Needs some shop time in Cary, NC