Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Need some help

Posts

Need some help

#1

Steven Antonucci

Need some help

steven antonucci

Water Gap Woodturners has suffered a terrible loss. Dick Plog, an all around great guy and friend to everyone, was killed in a car accident over the weekend. His widow has asked our club to make an urn for his ashes, and the group consensus is that I should be the one to turn it.

I've never been asked to do this before, so I am going to need the group's collective wisdom to pull this together. Anything that you guys can think of to help would be greatly appreciated.

Thanks

Steve

Re: Need some help

#2

What an honor

Jamieson

What an honor. I have made some that were hollowed through the bottom and put a cap/lid on it with stainless screws. The fit of the urn lid does not have to be air tight. The remains will be in a heavy plastic bag. You just need to make the volume needed so they fit inside. I don't have the dimensions now. I'm sure someone that is actively making urns will have the size required.

Re: Need some help

#3

Re: Need some help

Harry in Beautiful Downtown Kulpsville

If the cremains are to be buried, check with the cemetery to determine if they have any restrictions on size or the requirement for an outer container. Coincidentally, I attended a funeral today that did have a size restriction on the container.

The rule of thumb for container size is one cubic inch of volume for every pound of body weight. You might also consider using three or four inch PVC threaded pipe couplings. They can be mounted in both the body and lid of the urn without being visible when the lid is in place.

Re: Need some help

#4

Re: Need some help

Michael Mocho

Hey Steve, so sorry to hear about the loss of your friend. I'm certain that your intentions will be well expressed through your work, and appreciated.

Rule of thumb is about 1 cubic inch per pound of body weight + a bit more (for room to stretch?) I try to keep them around 220 cubic inches or so. The first one I made back in '86 was a wee bit too small, so best to err on the larger side.

One way to get a rough measurement is to use dry rice or beans poured into your urn from a box of known size that will be easier to quantify (for example 6 x 6 x 6 =216 cubic inches.

Hope the grain is with you and that inspiration comes in the process despite the sorrow.

best of luck,

-Michael

Re: Need some help

#5

Jim in Burlington Ont.

Re: Need some help

Jim in River Oaks, Ont.

Hi Steve,

Just been through this myself with a friend, my thoughts go out to you and all that were family and friends.

The calculation of volume is well known, go a bit bigger and look at some examples for ideas, maybe personalize it like I did with Barry's Box, what was his favourite woods etc... take your time and don't feel you have to be perfect, but just be your self.

You have the skills and imagination... go for it

Take care,

Jim

Re: Need some help

#6

Re: Need some help

Dave Long

Make sure you check with the funeral home handling the arrangements to see if there are any specific requirements regarding urns. There are different standards in different states although the National Association of Funeral Directors does list general guidelines for burial urns.

Re: Need some help

#7

Re: Need some help

Matt Overton

Steve,

Sorry for your loss. They have chosen the right man, let your heart speak thru the piece.

Re: Need some help

#8

Brad Vietje

Re: Need some help

Brad Vietje

Sorry for your loss, Steve.

If you can't figure out how to meet the time deadline, and don't want to use KD wood, I have some rough-outs that are air dried that might be big enough. Contact me if you want to see pix and consider those options to save time.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Need some help

#9

Steven Antonucci

thanks for all of the help

Steven Antonucci

Dick Plog was not only a WGW member, but he was also our club sawyer. We've located some folks that have stashed away cants that Dick cut years ago and hoping that they are air dried enough to be stable.

We also have a couple of folks volunteering to help with finishing. In the end, it will be our groups way of saying thank you and goodbye to our friend.

Steven