Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

something fishy

Posts

something fishy

#1

Keith Tompkins

something fishy

Keith Tompkins

Something new that's been on the back burner for a while. Turned and carved from holly, pink ivory, and ebony. the ribs are 1/8" diameter, the pupil is 1/16". A carburetor jet drill was used to drill the pieces for stringing. Any comments would be welcome.....

Re: something fishy

#2

Re: something fishy

John Lucas

Pretty cool Kieth. Hope to see you in Tampa.

Re: something fishy

#3

Not sure what a carburetor jet..........

JamieDonaldson

....drill is Keith, unless its actually a drill used specifically for drilling carb jets? What would make it different from a regular drill?

Re: something fishy

#4

Keith Tompkins

Re: something fishy

Keith Tompkins

Thanks John and Jamie. Jamie, the main difference is the size. The drill bit I used was .026 diameter..in comparison, a 1/16" drill bit is .0625.

Re: something fishy

#5

Dennis in Southern Oregon

Re: something fishy

Dennis in Southern Oregon

Keith, I am curious. It seems to me that aside from the gill and mouth grooves, the tail and head could be done with no appreciable hand carving by multi-axis turning. Was that your approach?

Dennis

Re: something fishy

#6

Re: Not sure what a carburetor jet..........

Joe shelton

They're all left-hand threads at the end, to mid-point, then transition to straight flutes to finish by reaming.

Nah. Just small diameter, except for the MOPAR ones.

Joe

Re: something fishy

#7

Keith Tompkins

Re: something fishy

Keith Tompkins

Hi Dennis, I think with a little planning, the entire piece could be turned. The mouth and gills could easily be turned using a pendant jig, and the tail could be turned as a larger ring, then sliced into multiple tails....However, this was my first attempt, just to see how it looked. Maybe next time it will be entirely turned.

Re: something fishy

#8

Re: Not sure what a carburetor jet..........

Steve Worcester.

Know them well, had side draft Webers in the 70s

Re: something fishy

#9

I envied you every time I...

Joe shelton

...synchronized my SUs. Mine was a MGB.

JOE

Re: something fishy

#10

Jim Evans

Re: something fishy

Jim Evans

Keith,

What did you use to string the fish?

Re: something fishy

#11

And I ran the dual SU's on my Bugeye .....

JamieDonaldson

....Sprite with velocity stacks, no air cleaners! So I did have to clean the jets occasionally! ;)

Re: something fishy

#12

Keith Tompkins

Re: something fishy

Keith Tompkins

Hi Jim,. I used beadalon bead stringing wire, .015" diameter.

Re: something fishy

#13

Keith Tompkins

Re: Not sure what a carburetor jet..........

Keith Tompkins

Steve, my Honda CB750 has four carburetors, and two sets of points. To run the way it should, it has to be right-on. :D

Re: something fishy

#14

Re: something fishy

Gerald Klug

I use a number 75 drill (.021") for my mouse whiskers but the twist drills that small are soooo easy to break. Is a carb jet drill beefier?

Re: something fishy

#15

Keith Tompkins

Re: something fishy

Keith Tompkins

Hi Gerald, I know a jet drill is designed for drilling brass, the particular one I used for the fish was a #71. I used a drill press, clearing the wood chips frequently to avoid straining the bit. I also use the lathe to drill with these tiny bits as well. I think drilling by hand would cause a lot of bits to break.

Re: something fishy

#16

Re: something fishy

John Lucas

Ideally those small bits require much higher speeds to cut efficiently. I have and use the sets that go from #80(about .0135") up to #60. I use the Dremel with a small jacobs chuck if I can. The higher speed really helps it clear chips. Using slower speed tools like a full size drill press means you need to remove the bit from the material very frequently to clear the chips. In wood I usuallly drill by hand supporting the piece and dremel with my hands against the workbench to keep the parts moving parallel. One of these days I'm going to break down and buy one of the jewelers drill presses. I've used them and they are a dream for these small bits. Quite expensive although the Dremel drill press would probably work but it's not nearly as accurate and smooth. When you buy a set of these buy 2 sets. The bits are easy to break and you will break the one you need the most at the worst possible time.