Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Sealer under lacquer

Posts

Sealer under lacquer

#1

Roger in MO

Sealer under lacquer

Roger in MO

What sealer is compatible with MinWax spray can lacquer (gloss)? Both cedar and walnut are soaking up the finish. I realize the open grain of walnut will require a filler of some sort or multiple coats, sanded between, to fill the grain but am looking for alternate.

Thanks

Re: Sealer under lacquer

#2

Re: Sealer under lacquer

John Lucas

shellac is a good sealer under anything.

Re: Sealer under lacquer

#3

Re: Sealer under lacquer

mjonesrdg

I've been using Crystalac* wood grain filler for open grain woods like walnut, oak, and mahogany. I am very positively impressed with the ease of use, and the result I get. Two coats of this takes the place of 5-6 applications of nitrocellulose lacquers. No affiliation, just very pleased. I get it from McFeely's or Rockler.

Re: Sealer under lacquer

#4

jim miles

Re: Sealer under lacquer

jim miles

If it is a turning, on the walnut try wet sanding on the lathe with Linseed oil- or similiar oil or even water - it will do a nice job of filling pores, grain and small imperfections.

Cedar is kind of "oily" Linseed oil doesn't work well on it.

Lacquer does fine over LSO

Re: Sealer under lacquer

#5

Minwax Sanding Lacquer Primer

Jorge

Which is the same Minwax lacquer plus a filler, looks to me like micro cotton fiber, works very well in trouble areas, where the grain is raised or rough. I coat the whole bowl or whatever give an extra to end grain or very porous areas, let it dry thoroughly, next day sand it down t the finest grit you use and is ready to spray. If it is a piece of very sound wood, no need of filler, just dilute lacquer 70/30 with lacquer thinner, apply a thin coat, let it dry a day and then sand and spray...

Re: Sealer under lacquer

#6

Roger in MO

Re: Sealer under lacquer

Roger in MO

Thanks for the responses. I will look for the products mentioned.

Roger

Re: Sealer under lacquer

#7

Re: Minwax Sanding Lacquer Primer

Hal Taylor

Jorge, curios what you sand with. Any kind of filler/sanding sealer gunks up what ever I use.

Re: Sealer under lacquer

#8

Ric Taylor

Re: Minwax Sanding Lacquer Primer

Ric Taylor

One of the reasons for using shellac as a sanding sealer is because it does not clog up sandpaper.

Ric

Re: Sealer under lacquer

#9

Re: Sealer under lacquer

Bob Rogne

Can shellac be used under tung oil?

Re: Sealer under lacquer

#10

Re: Sealer under lacquer

Don in Central Illinois

My understanding is that shellac can be used over or under just about anything.

Re: Sealer under lacquer

#11

Re: Minwax Sanding Lacquer Primer

Jorge

Hal,

I use 4 steel wool pieces from medium coarse to very fine (2, 0, 000, 0000) and the 220 wet dry followed by 320; the steel wool removes most of the sanding sealer and the wet dry smooths the works, it will still clog but a lot less.

Spray several thin coats. After drying, 0000 steel wool again followed by paper towels, kills the glare and leaves a nice sheen.

Re: Sealer under lacquer

#12

Mike Stafford

Re: Sealer under lacquer

Mike Stafford

Very late to this thread but I use Qualalacq sanding sealer. It is lacquer based, dries quickly and can be sanded to baby butt smooth. Spray lacquers work very well over it, after all it is lacquer. I top coat my turnings with Qualalacq lacquer when I want a shine.