That's almost exactly what I use daily
OSHA nightmare *LINK*
Posts
Re: OSHA nightmare *LINK*
#27
me three!
Re: OSHA nightmare *LINK*
#28Ah that's nothin, I saw a Yaqui
Mike Foster
Indian carver working in Mexico. I was at the beach and he came around selling carvings done in desert ironwood. I knew enough spanish to get him to take me to his workshop so I could buy some wood from him (also bought a couple of his carvings). His workshop was in a little cabana with just an awning overhead. His main power tool consisted of a free arbor driven by an electric motor that had a naked saw blade mounted. He'd fire that baby up, and hold the wood up to the naked sawblade to shape the wood. Eye protection, nah makes you sweat. Dust protection, well theres the wind that helps. Probably the scariest way of working wood I've ever seen.
Re: OSHA nightmare *LINK*
#29You've copied my design Ellis!

Re: OSHA nightmare *LINK*
#30
Re: Ah, it ain't so bad ...
Keith Tompkins
Dale, here's an easy, foolproof way to rip an angle on a table saw...First rip a piece of scrap (A) on the table saw. The sawcut now becomes a reference. Next, draw a line on the piece to be cut at the desired angle. (B) Now, line up the line you drew with the sawcut you made in the scrap piece of wood. Bandsaw away the waste on piece A, or tack a guide strip in place (C). I have even used double stick tape to secure a piece to be angle cut. Run the assembly through the saw without changing the fence setting...perfect every time, your angle will be exactly where you want it. no guesswork.No missing fingers. 
Re: OSHA nightmare *LINK*
#31Re: Ah, it ain't so bad ...
Dale Bonertz
Yes that works great especially if you are in your shop but then all sleds would work great. I am referring to making a quick cut on my job site table saw or bench saw (small table saw) at the job. This happens periodically that you need to make one or two quick cuts at an angle. I'll explain a safe method to do this on the job but I don't recommend this method unless you can see someone use it safely. If you are going to practice this method start by cutting and angle two inches long on the end of a 2' long board.
First I need everyone to understand that when I make these cuts it is generally out of either 1 x 4, 1 x6 or 1 x 8 MDF, oak, pine or fir and in lengths that are easy for one person to handle. For the sake of this example if I need a piece 2 1/2" wide on one end an 3" on the other and this piece needs to be 48" long. Pre-cut the 2 1/2" inch end on a chop saw to square it up, then rip the 5' to 6' long piece 3" wide. Mark your 2 1/2" width. Mark across the board your 48" length. Now draw with your 4' level or a straight board or snap a line from your 2 1/2" mark on the squared end to the 48" length which is 3 inches wide at this point. Notice I have not cut the piece to finish length yet, it is still 60" to 72" long. Now line your cut with the blade with experience you can get this close by eye while learning you can use anything fairly straight running along the blade and line up your line on the board. Always cut from the thickest end to the point (in other words start at the 2 1/2" mark and finish at the point of 3" wide and 48" length. Use your left hand index finger and thumb as the fence but you MUST keep your hand at minimum of 6" in front of the blade and it will also be to the left side of the blade. I tend to use the heel of my left hand to hang over the front edge of the saw to keep it from moving forward while cutting (this also allows for minor adjusting when starting the cut and my hand is about 10 inches from the blade). Now with a firm grip on the piece make your cut the piece will cut off well in front of your hand with no fuss or muss and fingers stay well out of the way and it is a safe jobsite cut. Once the angle is cut you can now go the the chop saw and cut to length. A hint for speed is don't pre-rip the board to 3" just leave it at 3 1/2" and cut through it to a point ,which may give you a 50" piece cut at an angle. It won't matter since you're cutting to length afterword anyway. (Side note I'll say again a table saw blade should only be high enough to cut through the piece and no higher, no exceptions and no excuses).
Please note I am all for push sticks and sleds and other shop safe cutting methods. Someone along the thread mentioned about their dad making these types of cuts on jobs. In your shop please use the other safer methods. I am explaining this for you so you all understand there are other safe methods of doing things when some shop tools are not available. Thus why I get a little defensive when we start knocking people in videos. It may be over site when they shot the video, they may be struggling financially and are doing the best they can or they may be Darwins. 
I want to go back to push sticks. Someone mentioned they use a push stick that has about a 1/4" notch so they can use it on thin material. These push sticks work great but if used a lot please inspect them regularly. They have a tendency to round over and can slip off the piece you're cutting. IMHO you are better off using a push stick near the thickness of the piece you're cutting up to around 5/8" thick push stick notch (there is a point of no advantage to go any thicker). Most of the push stick accidents that I witnessed in manufacturing were with the 1/4" notch type made out of plywood or hardwood. Hardwood types can get weak in the grain and snap off at the handle or notch as well they can round over at the notch. The plywood types don't snap off at the handle as easy but they round over at the notch easier than hardwood type material and can give you a sliver much easier.
Just remember there is no perfect answer to safety just perfect focus and diligence.
Thanks,
Dale



