Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

A wood-drying conundrum

Posts

Re: A wood-drying conundrum

#26

Re: A wood-drying conundrum

Mike Foster

John, I was just out doing some carving on it, and had my spray bottle with me. A great suggestion from John J. I think I knew this already, but just didn't translate it from turning into carving. At the first check, my instinctual reaction was to seal the end grain, and I used shellac for that. Spraying water is easier. Given the initial results with microwaving, I may use shellac to seal end grain and nuke the piece. Still going to continue the experiment though.

Re: A wood-drying conundrum

#27

Re: A wood-drying conundrum

Philip Duffy

Mike, Have you thought about ruff carving it to a minimum tolerance then boiling it for an hour? I like boiling as a way of relieving stresses built up in turnings and it may work nicely for your challenge. Try it on something of a test piece first.....and good luck. BTW, boiling does not dry wood to final %% but it sure moves it along the path.

Re: A wood-drying conundrum

#28

Re: A wood-drying conundrum

Peter Hyde

Mike there are a few postings on the 'net of using a microwave with the unsealed wood in a plastic bag. Don't seal the bag tightly as it will inflate. High power and it has to steam, then allow it to cool completely before zapping it again. Make sure you weigh it every time and when the weight stabilizes you're done. Commercial drying operations use steam because of the high humidity and the higher temperatures than boiling can reach. Also it relieves any stresses in the wood so reducing cracking problems even more. I've microwaved a lot of pieces but not used the plastic bag, just short bursts of high heat until it's too hot to handle then allow to cool. Very few cracking problems and sometimes a lot of distortion which I was hoping for.

Re: A wood-drying conundrum

#29

Re: A wood-drying conundrum

bill Crommett

For those of you that have investigated an industrial drying operation in action,you may remember that the hot vapor of the shed was overwhelming.

To get a high moisture content of the air in a microwave one has to eliminate the rapid exhausting of the moisture. I do this with a dedicated microwave oven that has most of the vent holes covered with duct tape to keep the moisture from dissipating too rapidly.

This process is much the same as turning the plastic bag inside out, but because you are working at higher temperatures the process is speed ed up.

It works for me.

Re: A wood-drying conundrum

#30

be careful...

GaryG in MD

Microwaved wood doesn't generally get hot on the outside until the inside catches fire.

Always store microwaved wood in a metal can for a number of hours after you heat it, just like you would with fireplace cinders. ...GG

Re: A wood-drying conundrum

#31

Re: be careful...

Mike Foster

I am pretty sure the wood is not getting warm enough for that as I am heating for very short bursts. I guess it is possible that is getting hotter inside, but I will play it safe and put it in a safe place after nuking it. I have had one house fire and do not care to relive that experience.

On a related note. I used to live in Cortez, CO. Pretty much nowhere, and found a guy that lived pretty near me. He made some pretty amazing urns (pyramidal in shape) from some amazing wood. He actually made as much processing burls and reselling them as he did from his craft. To give you an idea of the scale of his operation, he had 2 outdoor hay barns FILLED with burl slabs for resale. His shop had 4 14" bandsaws all lined up, each dedicated to one operation for his urns. He had forklifts. A major bandsaw mill... You get the idea. I got some great burl from him.

Well he told me a story that I will never forget. He was a volunteer fireman, and while working in his shop he got a call for a fire and rushed off to the call. He failed to remember that he was nuking some wood for one of his urns. He must have had a microwave that either had a manual shut off, or the timer didn't work. You guessed it, while he was fighting one fire, he got a call for another, his shop. It was a total loss for him. Not sure what all he lost, as I saw the place after it had been rebuilt.

So needles to say, I have only been warming the wood. It has never been more than warm in my hands. Hot just scares me enough.

The experiment is continuing, but it looks like sealing the end grain will be the answer. I'll post once I get to the point it stops losing weight.

Re: A wood-drying conundrum

#32

Re: be careful...

John Lucas

Mike I was microwaving a piece one day and at that time I would gradually increase the time each cycle until I was using more than a minute. Apparently there was a sap pocket in the wall of that bowl and it burned a black hole in the piece. Never did catch fire but it smelled up the microwave and took about a month to get rid of the smell. I now have a microwave in the shop dedicated to turnings.

Oh and they will get pretty darned hot on the outside. Once they start to get dry and I've run the time up a little they can get pretty darn warm on the outside. I don't think I would call it hot but you don't want to hold it very long.

Re: A wood-drying conundrum

#33

pc power supply converted into a pyrography machin

george krise

Hello

Back in 2005 Ben Aragon posted instuctions on how to convert a pc power supply into a pyrography machine. I can not find Ben online but I noticed you posted comments about this project. I have built the pwm and it works to power a 12 volt fan but there is not give the wood burning pen enough power to get hot. Do have any idea what the problem could be?

Thanks for your time and help George