Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

thinning wipe on poly

Posts

thinning wipe on poly

#1

thinning wipe on poly

John Lucas

Well as near as I can tell the wine saver spray does not do a thing and maybe even worked worse than just air. I have religiously squired the wine saver into the can of wipe on poly every time I've used it. I have about 1/2 can or even more and it's getting really thick. I normally get about a 1/2 can used before I decide to toss it.

Anyone know of a way to thin this stuff. I have used mineral spirits in the past and it does seem to thin it but I'm not sure it finish works as well as when it is fresh. I'm getting tired of only getting half a can of use out of the stuff. I had the same problem with Watco danish oils when I used them but will gladly read any responses about that stuff or any other wipe on finish.

In the winter it's just hard to spray lacquer. I have more problems that it solves and just can't spray indoors at all due to breathing the stuff and using flame heaters.

Re: thinning wipe on poly

#2

Mike Stafford

Re: thinning wipe on poly

Mike Stafford

John, I found that wipe on poly would get thick just as you describe so I started thinning it outside the can in small cups or jars. I thin only the amount I am planning on using and then use it up in a day or two. Much longer than that and it seems to thicken up.

Maybe there is a better solvent that would not cause this thickening problem.....

Re: thinning wipe on poly

#3

Re: thinning wipe on poly

Dick Coers

Naptha will work better than mineral spirits. I keep crushing the can (squeeze the sides of the can) as I use it, so the fluid stays up near the lid. I still end up throwing some away, but way less than half a can.

Re: thinning wipe on poly

#4

Re: thinning wipe on poly

david

Perhaps experimenting with a small amount of your poly decanted into a small covered jar will lead to a solution. If added water will stay on the bottom and the poly floats above the water, then filling the jar to the rim by adding water will eliminate the air in the container and give you a longer shelf life.

Re: thinning wipe on poly

#5

Jim Evans

Re: thinning wipe on poly

Jim Evans

I make up 3 small clear ketchup type bottles thinned with lacquer thinner 25%, 50%, full strength.I start out with the 50/50 mix for a couple of coats, then 25% thinner/75% poly for a couple of coats, then full strength poly.

The number of coats depend on the piece and depth of finish that I want.

Re: thinning wipe on poly

#6

Re: thinning wipe on poly

bill Crommett

An old mariner's trick is when capping up a varnish can, to take a big breath and hold it to exhaust all the oxygen then blow off a little (the air in the dead space) and blow a big breath of the used-up air into the can and quickly cap it to keep the CO2 in and the oxygen out. (Then take a big breath before you pass out from anoxia).

Re: thinning wipe on poly

#7

Re: thinning wipe on poly

John Lucas

Bill That's what I thought squirting the wine saver into the can was supposed to do. Replace the air with something else that won't deteriorate the finish. Apparently it doesn't work. Either that or that can of innert gasses that feels like it doesn't have anything in it, really doesn't have anything in it. :)

Re: thinning wipe on poly

#8

Re: thinning wipe on poly

John Lucas

If I can find the jars I may decant what's left into 3 separate containers and thin one with mineral spirits, one with lacquer thinner and one with Naptha and see if I can tell a difference. I'm headed to town in a few minutes. I'll buy some baby food and empty the jars. Anybody want some strained spinach and potatoes. :)

Re: thinning wipe on poly

#9

Re: thinning wipe on poly

Bill Jacksonville, NC

Solved problem of throwing away wiping poly/varnish mixing my own. I buy finish in pint cans and mix with solvent (mineral spirits or naphtha). I use 50/50 mix of finish and solvent. Use an inexpensive reusable measuring cup and ounce scale from Wal Mart. Not very technical using ounce scale, have no idea what to do with other scales on cup. Normally use one ounce of finish to one ounce of solvent goes long way.

You can find official graduated paint mixing cups in many sizes at auto paint or parts stores. They work well if spray a lot. They come in reusable or throw away cups.

Should never use more than 60% solvent in a wiping varnish. I do when finish more than year old. Commercial products often contain as much as 70% solvent. When directions say shake don’t stir kind of a clue.

Since started mixing as needed have not thrown away any finish. I stopped using Watco several yeasr ago. If read ingredient list think Watco more an oil varnish blend with more solvent than oil or resin.

Re: thinning wipe on poly

#10

Ellis Walentine

Re: thinning wipe on poly

Ellis Walentine

Once the varnish starts to polymerize in the can, thinners will be less effective, but either naphtha or mineral spirits should work. I agree with the baby food jar route. Finishes last a long time and you can just throw out the jar when you're done with it. Another trick is to add glass beads or marbles to replace finish you've used.

Ellis

Re: thinning wipe on poly

#11

Re: thinning wipe on poly

John Lucas

I mixed 3 batches. The minwax was really starting to gel. I used Mineral Spirits, Lacquer Thinner and Naptha. I'll have more results tomorrow when the patches I rubbed on glass have time to dry.

All 3 seemed to work. I added appox. 1/3 of the thinners to the minwax. On application the Mineral spirits was more Oily or maybe a little thicker. It was hard to tell. The other two seemed thinner. That seemed to bear out when I rubbed them on glass. The mineral spirits looks like it wants flatten out better although when you rub it into the wood I don't think it matters much because it's pretty thin.

Re: thinning wipe on poly

#12

Re: thinning wipe on poly

John Lucas

I checked the glass this morning. All 3 work just fine. The finish dries nicely and is firmly attached to the glass.

some thoughts that I will probably find out later in the next few weeks. It's been my experience that lacquer thinner and acetone eat up the plastic lip on baby food jars so this may not be the best solvent to dilute with if you (or me) insist on using baby food jars. Don't know about naptha yet but I do know that mineral spirits won't eat up the rubber for a long time anyway.

another thought. Baby food apple sauce is blended much finer than the same stuff you buy in plastic jars on the fruit isle. It tastes the same and costs about the same however so it wasn't a bad purchase since I would throw out the plastic jars. :)

If anyone knows of a better place to get glass jars of the appropriate size I'm all ears. Canning jars were much larger and a lot more expensive.

Re: thinning wipe on poly

#13

Mike Stafford

Re: thinning wipe on poly

Mike Stafford

John, with this long quality report and evaluation on the merits of baby food I was just wondering if you are expecting to have to start gumming your food?

I knew you were old and I knew you were retired but I did not realize you were old, retired and toothless..... :b :b :b

Re: thinning wipe on poly

#14

Mike, you didn't mention pregnant!?


Re: thinning wipe on poly

#15

Re: thinning wipe on poly *LINK*

Stuart Johnson

These might work.


small glass jars

Re: thinning wipe on poly

#16

Re: thinning wipe on poly

John Lucas

Baby food jars were .52 at Krogers and you get to keep the apple sauce. :)

Re: thinning wipe on poly

#17

I am expecting-  to win the lottery 


Re: thinning wipe on poly

#18

Re: thinning wipe on poly

bill Crommett

Doesn't every one have grandchildren this time of year ?

Re: thinning wipe on poly

#19

Apparently Bill

John Lucas

My cousin's baby is due on the 24th and one of my coworkers child is due on the 23rd.

Re: thinning wipe on poly

#20

dick ,ialso squeeze the cam