Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

beaded finial

Posts

Re: beaded finial

#26

Re: beaded finial

charlie belden

Keith:

Did you undercut where the tenon meets the underside of the bottom of the finial? By making where the finial meets a curved surface (glass bead) concave, it will fit down around the curved surface of the glass bead rather than sitting ON it. It appears that you did - but it's worth pointing that out.


Re: beaded finial

#27

Keith Tompkins

Re: beaded finial

Keith Tompkins

Hey Charlie, Yes, I did. the bead is curved, and made by hand, so it's got imperfections. Undercutting helps.

Re: beaded finial

#28

Keith Tompkins

Re: beaded finial

Keith Tompkins

Good illustration Charlie, but the tenon goes half-way into the base!

Re: beaded finial

#29

Upside down!!

Bob Edwards



Forgive me Kieth but I had to try this. I was always told to view a turning upside down and it would show the balance of the piece. Once I did that my wife insisted I do an ornament. She prefers ornaments that are lite and more delicate than the usual. It may take some refinement but I feel the idea is good and I enjoyed doing it. I would like to find some slightly larger beads and so far haven't found any commercially available. As usual your work is an inspiration!

Thanks again.

Re: beaded finial

#30

Bob Moffett

Re: beaded finial

Bob Moffett

I think I would like it better if the sharp edge above the bead was rounded, but that's just me. I still think it is a beautiful finial.

Re: beaded finial

#31

Jim Barbour

Re: beaded finial

Jim Barbour

Hi Keith ~

Gorgeous piece. I agree that the top and bottom are not quite matched and, rather than a full-scale redo, it seems that if the last bit of the top, where the fillet meets the bead were to be lined up with a matching fillet on the other side where the bottom meets the bead, it might be improved (giving the illusion of two diagonal lines crossing the bead).

On a slightly different note, I use slivers of bamboo to hold tops and bottoms together through a bead, ball, sea urchin, etc. The bamboo is plenty strong to hold the parts together even when very small. I just drill the top and bottom before turning and glue an appropriately-sized sliver in both parts through the urchin, or whatever is in the middle. The bamboo is readily available in grocery stores in the oriental foods section. Just split it to whatever size you wish, down to 1/32 or so. That way you don't have to worry about exposing the tenon -- unless you are cutting it REALLY small!

I look forward to swapping notes at the NC Symposium - you never fail to teach me and get my creative juices flowing. Thanks.

Re: beaded finial

#32

Bob Moffett

Re: beaded finial

Bob Moffett

Jim, I have started doing the same sort of thing with my ornaments, except instead of using banboo (which is a good idea but, I have never thought of it), I use a round toothpick. Same principle, different material.

Re: beaded finial

#33

Keith Tompkins

Re: Upside down!!

Keith Tompkins

It looks great!

Re: beaded finial

#34

Keith Tompkins

Re: beaded finial

Keith Tompkins

Thanks Jim....I can't believe this thread is still going! Look forward to seeing you in NC! Keith

Re: beaded finial

#35

Jim Barbour

Re: beaded finial

Jim Barbour

Keith when you do good work people pay attention for longer. It is a delightful piece and they will only get better as you do more of them. What's the expression? -- something like 'you don't know what you are doing until you have started the second hundred' I suppose that applies to modifications of something we have done thousands of times as well as to something new.

Re: beaded finial

#36

Keith Tompkins

Re: beaded finial

Keith Tompkins

Well, Thank you Jim! :)