Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

DIY Video System for Demonstrations *LINK*

Posts

Re: DIY Video System for Demonstrations *LINK*

#26

Other video systems

charlie belden

I posted this DIY video system for turning demonstrations over on WOW and got some systems other folks have come up with.

Jamie Donaldson superised the video stuff at AAW symposiums for three years and put together an article on a video system for demonstrations. The article is in the Best Practices section of the AAW site. There are three cameras. One is on a dollied tripod with an operator, that's on the tailstock end and can be moved around to get the best shoot. There is also a fixed camera on a stand on the headstock end that apparently can be zoomed in and out with a wireless remote. The third camera is out in front of the demonstrator and lathe and is also on a stand, again presumed to be operated with a wireless remote.

I think this is what Jamie was describing in his article.


The article doesn't give any specifics on lighting or how and where the lights should be positioned.

This system requires at least two people to operate and it seems to need a lot of wires - video and power - on the floor around the demonstrator.

Another system - what seems to be a Dream System was pointed to by Mark Hancock - the Surrey Association of Woodturners. It appears to have a remotely panned and tilted as well as zoom in/out camera on a VERY tall stand - two additional fixed cameras (with remote Zoom?) and a professional looking Master Control Station, complete with diamond plate case. Then venue for the event shown also has a VERY tall ceiling height, an elevated stage, a huge movie screen and must have a pretty good video projector as well


Have you got an illustration or some photos of the Video System your club has - with a word description of it you'd dcare to share?

Re: DIY Video System for Demonstrations *LINK*

#27

My set-up only requires 1 camera...........

JamieDonaldson

...operator, who also operates the switcher to select the camera that offers the better view at that time. The best camera operators are woodturners, who can understand and anticipate the demonstrators methods. The 2 stationary stand cameras were simple fixed lens chip cameras already owned by AAW, and lighting was the regular Sanders lathe fixtures, but with a CFL bulb to diffuse the output, and eliminate much of the camera image bloom due to overexposure. This was a basic set-up, dictated by the equipment available, and don't forget that there were usually 16 demo rooms in operation.

Re: DIY Video System for Demonstrations *LINK*

#28

Re: My set-up only requires 1 camera...........

charlie belden

Thanks for the clarification.

So

- you have two fixed cameras that aren't remotely "zoomable"

..one looking down over the headstock at the area being turned

..one looking in from in front of the turner at about tool rest height

- one human operated manually zoomable camera, on a tripod on

..wheels, looking in from the tail stock end of the lathe

- the human operated camera operator also has a Switcher Box

..connected to all three cameras AND to the display device the

..audience can watch - and that all the connectioned devices

..(cameras and dsiplay proector or flat screen) are wired to the

..Swithc Box.

- the human camera's operator functions as both camera person

..AND Switch Box operator

Questions:

If the camera operator also acts as the Switch Box operator, how

does he/she see what each of the three cameras is seeing in order

to know which camera has the "best shot" to send to the audience

display? Without a display at the camera operator's location, for

. .EACH of the three cameras, how does he/she know which camera

..has "the best shot" - in order to switch it to the audience display?

Assuming the video system is NOT wireless, there seems to be

at least five wires connected to the human operated camera location

- that human operated camera's power cord

- that cameras video cable to the switcher box

- a video cable from the fixed headstock view camera to the switcher box

- a video cable from the front view camera to the switcher box

- a video cable from the Switcher Box to the audience display device

And if the camera operator also has a display for each of the other

two cameras, you'd have to have splitter cables for each, one leg

to the operators location display and one leg going to the Switcher.

That seems to be a lot of stuff to have on or near a camera that

can be moved around for a best shot. How are all these components

connected to or mounted on the moveable operator's camera set up?

If the human operated camera, which I assume is on a dollied tripod

so it can move around to get its "best shot", has FIVE wires/cables

attached to it, seems the camera Operator / video feed Swticher would

have to be a Wires Wrangler as well. That's a lot of tasks for just

one person to handle, especially during a live demonstration. In

a "studio" setting, where you can say - "Cut. Let's try that again."

- or - "Cut. Next camera set up please." - the logistics required,

and the delays associated with them, would be no big deal. Wih a live

demo, showing what's going on, as it's happening - that's a bit more

difficult.

Do you have any photos or illustrations of the system you

recomend?

Re: DIY Video System for Demonstrations *LINK*

#29

Re: My set-up only requires 1 camera...........

John Lucas

Charlie That's exactly why I like the one camera on the boom arm. You don't have to switch. you don't have all the wires and don't have the expense of monitors for each camera to see what they are doing.

It's not perfect either of course but I think the expense to the club is considerably less. One camera with remote zoom. The Boom arm can be built with off the shelf parts. I am working on an improvement in the swiveling part of the camera mount, just haven't worked out the details yet.

Re: DIY Video System for Demonstrations *LINK*

#31

Single Boom Arm Camera...

charlie belden

While a single, boom arm mounted, moveable camera simplifies things

- no need for a Switcher and all the wires needed for it

- no need for multiple displays - one for each camera

- only need one person to operate

- less expensive (one vs 3 cameras, and no Switcher)

- only one piece of hardware and accompanying wiring to keep track of,

..set up and store - that doesn't weigh much

I have a few questions about it.

1. How easy is it to be damaged, either in use or when stored & moved?

2. With the single operator watching the camera's display while

.....at the same time moving the boom and camera angle around

.....while maybe zooming at the same time,

....- not getting in the way of the demonstrator, or hitting him/her

... ..seems quite a few tasks for the operator

. . - what about conflicts between camera and lights?

With the Three Camera Fixed On A Stationary FRAME, that also

supports the lights, nothing has to move - expcept the lens

being zoomed in or out. Once set up, assuming it's set up

to not interfere with the demonstrator, the Operator only

has two things to do

- watch the camera feed displays and pick the best shot to

..switch to the audience display device

- zoom a single camera in or out to get a detail shot

Re: DIY Video System for Demonstrations *LINK*

#32

Re: Single Boom Arm Camera...

Jeff Brockett

We used the single camera setup on the boom that John Lucas described for two of the TAW 2012 symposium demonstrators and have used the same setup the entire year for all the TAW monthly club demonstrations. The rig holds up well to storage and traveling, is lightweight and easy to handle. We have a wired remote control rigged up to the camcorder that allows the camera operator to zoom in and out as needed. Our survey feedback from the 2012 symposium was that this was the best setup that we had used. We are experimenting with a second Go Pro brand camera set up to look directly at the headstock view and are seeing good results with this setup. Each camera feeds into its own large flat screen television. The boom camera is on wheels and can be moved as needed to get the best view. As mentioned by many regardless of the setup quality is dependent on the camera operator.