Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Redtop Box

Posts

Redtop Box

#1

Redtop Box

Philip Morris

This is a little box (approximately 2" diameter), turned from a branch of a Redtop Photina shrub. Blank had pith included. Saw something similar in Richard Raffan's Turning Boxes where he positioned pith to one side, liked the way it looked so thought I would try something similar.

Finished with a couple of coats of Formby's Tung Oil finished then buffed to a high gloss.

I apologize for the reflections in the photos (taken on kitchen counter).

C&C welcome.

Philip



Re: Redtop Box

#2

Re: Redtop Box

John Lucas

Nice box. Love the dimensions and placement of the details. Photos aren't bad at all.

Re: Redtop Box

#3

Chuck Jones - West TN

Re: Redtop Box

Chuck Jones - West TN

Very nice. I like the box and the wood.

I turned a vase for my daughter from a photenia bush in her yard that was dying from the fungal disease that is affecting most of them. Noticed today I still have a few small pieces. Never thought about a box.

Re: Redtop Box

#4

Re: Redtop Box

Roger Chandler

Fine piece of work on this one.......good details and beautiful finish. Nice proportions on the lid and body........excellent!

Re: Redtop Box

#5

Re: Redtop Box

phillip medghalchi

Beautiful work, and second all of the above. I am struggling to figure out my box lids procedure. I just came in form the shop and worked on a Japanese style box, however, I got to see what happens tomorrow. All I did was to shape the top and bottom with two tenons on each side then I separated the whole thing until the next step. Which I have to figure that out.

Your piece is very nice in proportion.

Re: Redtop Box

#6

Re: Redtop Box

Philip Morris

I also rough the external profile of the box while the blank is between centers, which is a deviation from the procedure outlined in Richard Raffan's Turning Boxes. Prior to this, I my lids tended to be disproportionately too tall for the base.

Just don't forget to allow for the base flange and parting cut when roughing the profile between centers.

Re: Redtop Box

#7

Don Leydens

Re: Redtop Box

Don Leydens

Philip, in my opinion, you absolutely nailed this box. The shape, design, detail, grain position and finish are all top notch. This is certainly a box to be very proud of!!!

Re: Redtop Box

#8

Re: Redtop Box

matt overton

I agree, this is a great little box

Re: Redtop Box

#9

Excellent!


Re: Redtop Box

#10

Keith Tompkins

Re: Redtop Box

Keith Tompkins

Good one! The joint doesn't break the form....nice work!

Re: Redtop Box

#11

nice form and execution

GaryG in MD

I really like everything about it. Nice one! ...GG

Re: Redtop Box

#12

Joe Bradshaw

Re: Redtop Box

Joe Bradshaw

Phillip, that is one good looking box. Only one thing to change, and that would be to have it on my shelf instead of yours.

Re: Redtop Box

#13

Re: Redtop Box

Philip Morris

Joe,

Thanks. Actually, all I have now are the pictures. Delivered to the new owner last night.

Philip

Re: Redtop Box

#14

Mike Stafford

Fabulous Philip!!!

Mike Stafford

This is one of my favorite box forms to turn. I call it an inset dome and you did a fabulous job of executing the design.

I particularly like the way you used the arching end grain to its best effect. Your continuation of the box form through the beads is perfect. The two beads at the join give you just enough purchase to pull the lid off if it becomes tight. Your finish is spot on.

I bet that is one sweet little box to hold and hide some little treasure.