Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Have any of you ever turned rich pine?

Posts

Have any of you ever turned rich pine?

#1

Have any of you ever turned rich pine?

Keith Newton

For over 20 years I have kept a rich pine burl, about 14" D, that I have been waiting for inspiration to strike me. But then had reluctance to even use it, due to it being a fire hazard. It is about as volatile as a diesel soaked rag.

However, I have a job coming up where I will be using some air-dried pine. I plan to roast it for a few days to set the pith, and it has dawned on me that I could rough out a blank, then add it to other.

I always thought I would turn it thin, and try to saturate it with some other thin product, to add to the translucence.

Any experience or suggestions here?

Re: Have any of you ever turned rich pine?

#2

Mike Stafford

Re: Have any of you ever turned rich pine?

Mike Stafford

Around here it is sometimes called heart pine and as you say it is very volatile and we used to call the knots that you describe "lighter" knots because of what a good job they do in helping to start a fire. Split or sawn into pieces they are sometimes referred to as "fat" kindling.

I have turned it a couple of times for special requests. It will gum up your tools terribly. I had to soak the pitch off with turpentine. However i learned that you could minimize the gum buildup somewhat by waxing the the tools with paste wax and then spraying them with kitchen cooking spray.

Sharp tools and fine cuts are essential. You not only do not want to sand this wood it is nearly impossible to do so without changing your paper with every revolution of the lathe. You can try cleaning the surface frequently with acetone but I only had limited success with that method.

I hope someone has better ideas because I have been asked many times to turn things from this wood and I have learned to gracefully refuse.

Re: Have any of you ever turned rich pine?

#3

Mike Mills

Re: Have any of you ever turned rich pine?

Mike Mills

I have never turned it but I did make a flat project, ONCE. Mike is correct, on a 3” X 4’ long board you are lucky to get one pass with a 5” sanding disc.

I still have two sections salvaged from a barn my G-grandfather built about 1892 (that is the only reason I keep it).

I have thought about trying to turn some of it and maybe John’s ideas with the wax and cooking spray will work.

From working with it, be careful on the lathe. Due to the high rosin contend it is fairly weak and brittle. Not sure how thin you can turn it without it shattering.

Re: Have any of you ever turned rich pine?

#4

Chuck Jones - West TN

Turned a pen from a piece once.

Chuck Jones - West TN

It was one of the nicest pens I have ever turned... which isn't saying a lot because I don't turn many pens.

My brother-in-law lives in northern Louisiana and uses wood heat. He harvests "fat wood" for starter. Brings it to me in large chunks. I made the pen for him. I rarely us it even for fire starter in the shop so it accumulates... just in case you need any more.:)

The pen is all I have done with it and needless to say that was not a fair test.

Re: Have any of you ever turned rich pine?

#5

Re: Have any of you ever turned rich pine?

Ralph Watts

Rich,

A friend brought me a 250# chunk of fat pine and we turned it into an outdoor sculpture. Fat pine will last forever outside--with a little checking.

You have to love the smell of turpentine to turn this stuff and expect your shop to smell that way for several weeks. I didn't have any problem with sticky tools and didn't sand after the first try with a very coarse grit. I thought it cut exceptionally smooth, probably from all the turp. Cabinet scrapers work great for the final finish. Turning it thin gets you a lovely glow with a light inside (use LEDs) and no further treatment is necessary. Besides what can you get to stick to a surface coated with turp? Maybe lacquer if you prewipe with acetone? We left ours unfinished.

About every 10 min or so I had to stop and clean off the bottom of my shoes. The shavings will stick to each other and everything else. The build up was at least 3/4 of an inch... However all the shavings started fires in my shop stove for a couple of years.

Best regards, Ralph