The Sorby Spindlemaster is among the ......
JamieDonaldson
...most useless tools I've ever bought. It couldn't even be used to open a paint can! 
Knowledge You Can Build On — Est. 1998
The Sorby Spindlemaster is among the ......
JamieDonaldson
...most useless tools I've ever bought. It couldn't even be used to open a paint can! 
Sounds a lot like the fluteless gouge
Ken Vaughan
Doug Thompson is selling these in two sizes now --
I have and use several different skews.
Don Orr
I use oval section skews a lot for fine details. The included angle is as they came from the manufacturer, probably about 25 deg. I only hone them with the Lacer diamond slip stone and strop on leather charged with white diamond buffing compound. (An old carvers technique). These rarely go to the grinder unless I get a nick in the edge. I like the straight edge and flat bevel on these as well as the really sharp long point.
I use a 1/4" round skew like the Rosand style (got the steel from him and the directions on how to make it) for really little things. Also a straight edge and flat bevel that is honed and stropped.
I have the large Lacer skew for big planing cuts and roughing.
My actual favorite is-wait for it-a Harbor Freight skew from the cheap "HSS" set. I modified it into a Lacer-like profile. Rounded edge on the short side and slightly eased edge on the long side with a curved cutting edge and an included angle of about 30-35 deg. and a slightly convex bevel. This is also only honed and stropped as above. I put a nice long fat handle on it and this thing cuts like butta. Edge retention is not fantastic but a quick hone and strop and back to work. (See a pattern here?)
I saw Keith demo his V-Skew and it works as advertised. Didn't get to try it yet.
Then there are the parting tools and bedans used as mini skews as well as the British-termed beading & parting tool also used in skew fashion as mentioned in an above post.
Re: So tell me, what skew do you like and why
charllie belden
Being a ToolPhreak, I have a 1 1/4", 1", 3/4" and 1/2" skew, all but the half inch with full sized handles, the half inch handle is only 4" long -all of them with a curved cutting edge (that LONG point was just too scary - and got in the way sometimes). I don't worry much about the bevel angles, but probably stay in the 35-45 degree range. For tight spaces I use a 25 degree bevel angle bench chisel - because I set my WorkSharp sharpener to that preset angle (there are three others as well). The 1/4" bench chisel works just like a thin bedan and cuts are initiated with either corner of the tool.
I've only got a JET Mini, with a "nominal" swing of 10", but a "practical swing" of maybe 7 1/2" since you have to dismount your turning to move the banjo and toolrest from one end of the piece to the other. Since I seldom do bowls at the 7 1/2" diameter capacity of my lathe, I don't use the two larger skews, For small lidded boxes, ornaments, finials, the outside of small hollow forms and miniature plates and bowls, I use my 1/2" skew for both cutting and scraping. I use the 1/2" to hollow boxes - used as a plunging scraper - the "long point" doing all the work.
I prefer the rectangular cross section over an oval cross section, probably because I can control the tool better. But from a torque perspective, the oval keeps the cutting edge more over the tool rest than does the rectangular cross section.
If a straight skew gives you trouble, try putting a curve on the cutting edge.
Re: Sorby Spindlemaster ??
charllie belden
I bought a SpindleMaster, before I was shown how to put a curve to the cutting edge of a skew and after I had my first catch with a straight edged skew. Less scary than a skew, but can still produce a spiral cut OOPS. They're also pretty thin so reaching out past the tool rest than get a bit twitchy. The round bottom tended to roll on its own rather than when I wanted to do a rolling cut. The SpindleMaster now sits in my tool holder.
Re: So tell me, what skew do you like and why
Bob Edwards
Without going into grinds and angles etc. My favorite and most used skew was given to me by Bob Rosand.
It made from a 1/4" HSS drill rod.
Re: So tell me, what skew do you like and why
Leo Cuellar
Hi John, I'm finding that new favorite skew chisel isn't a skew any more. Just a straight grind 90 degrees to the sides, with a typical bevel angle. I have 2 now, a 1" and a 1/2". Very good for planing & cutting beads works great as you can use both corners of the tool. Works as a wide parting tool as well.
Re: So tell me, what skew do you like and why
johh lucas
Leo Are you talking more like a carpenters chisel but with a grind on both sides instead of one flat side? I just made one of those and kind of like it except I'm a real fan of the long toe for a lot of cuts so will have a hard time giving up the angled grind.
Re: So tell me, what skew do you like and why
Leo Cuellar
You could certainly make one that way, I was lucky to have a spare leaf spring blank for one. For the smaller one I reground a Grizzly captured ring tool from their beading set that I could never get a satisfactory bead from. It is pretty decent steel, will take a fantastic edge, but something about the geometry, or me just didn't work out. I won't retire my traditional skews either, but have found that it is pretty hard to get a spiral catch when making beads once you get used to the way the straight grind cuts. Probably handles similar to a bedan, I would guess as I've not used one yet. The grind is something that was mentioned in older British turning book, and seems to work well. I'll make one more at 1/4" for doing smaller work.
I'll probably also play with some different bevels as well.
I had try it right away.
Leo Cuellar
John, just made the little one and tried it out.
This was done on a 1" block of curly maple that I'd taken a few swipes at with my new Hunter #3, but all of these cuts were done with the straight ground chisel in the pic. I couldn't take it down any smaller than 1/4" at the thin spot because I noticed it had a crack running the full length, just visible in the photo. The vibration that caused made me stop. It makes horrible pummel cuts.