Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

jewelry findings not sticking to wood..

Posts

jewelry findings not sticking to wood..

#1

jewelry findings not sticking to wood..

darrin hill

so is wood wood, or do different woods react differently to adhesives? I'm trying to get metal pendant bails to stick to the back of some pendants, and the superglued ones just snap off if i try to pull them off... they don't just pop off easily, but a good pull on one will just pop it off.. and I'm sure someone who got one would gripe about it. I tried a 2-part 20 minute epoxy last night, but after a couple of hours it was still not cured and was not stuck, so i might try to get a fresh tube of epoxy later..

just want to know what you guys have found or recommend...

the woods i am using are cocobillo, jobillo, spalted maple, hard maple, walnut, purple heart, iron wood, bicote, asian satinwood (Not sure of that name, but it was on the blank i got from woodcraft) and whatever else i have on hand,...

Re: jewelry findings not sticking to wood..

#2

Re: jewelry findings not sticking to wood..

darrin hill

just got back from the shop...

the epoxied ones didn't stick at all...

forgot to mention that last night i took a dremel and scuffed up the back of the bails and the wood where they were going to make contact with..

epoxy doesn't work at all...

however, the one i did scratch and put a medium viscosity Ca glue on has stuck rather well.. might try the superglue again...

but further recommendations are welcome..

Re: jewelry findings not sticking to wood..

#3

Dick Hines

Re: jewelry findings not sticking to wood..

dick hines

SWome of those woods are oily. CA would not be the best glue for them. On the "bonsai" handles I do on my boxes I use JB Weld. The only trouble I have with it is that it is dark gray when mixed so I have to be really careful when useing it on light colored woods.

When I glue in a handle I always cut a couple of groves in the femal e top and in the male handle to give the glue something to hold to.

Not sure how you could do that with what you are doing. Can you drill a small hole in the bails and put a pin in the hole?

Re: jewelry findings not sticking to wood..

#4

Alan Zenreich

Re: jewelry findings not sticking to wood..

Alan Zenreich

I would not trust a glue joint on a small bail.

I've used CA or epoxy on brooch pins, but that's about it.

For our pendants there is always a mechanical connection either a hole through the pendant, or a glued in pin, or tiny eyescrew drilled into the top edge of the pendant.

I would be happy to chat with you about these options, if you like... drop me a private email and I can send my phone number.

Re: jewelry findings not sticking to wood..

#5

Re: jewelry findings not sticking to wood..

john lucas

I use epoxy with great success, but I use pendants that have small holes in them. The epoxy squeezes up through these holes and forms a sort of rivet. I wonder if the pins have some sort of unusual finish on them because I've had the smooth back ones pop off as well. The glue sticks to the wood but comes off the pin. I scuff the back with sandpaper of my dremel to aid in adhesion.

Re: jewelry findings not sticking to wood..

#6

Not all CA created equal...

mjonesrdg

And, I am not an authority on the subject, but, pen turners may have some good sources of info, or, you might give the folks at Starbond a call. I am aware that some of the products are better than others for adhering metals to wood.

Re: jewelry findings not sticking to wood..

#7

Phil Stivers

Re: jewelry findings not sticking to wood..

Phil Stivers

I am experimenting with an adhesive called E6000. A glass artist swears by the stuff for attaching glass to wood et al. I don't have any results yet (that back burner thing), but you might look into it. The adhesive is not very expensive.

Re: jewelry findings not sticking to wood..

#8

Re: jewelry findings not sticking to wood..

john lucas

I've heard e6000 recommended many times. I have yet to use it but need to get some and start experimenting.

Re: jewelry findings not sticking to wood..

#9

Re: jewelry findings not sticking to wood..

Jim Pugh

Years ago I made some wooden belt buckles and used Tandy Leather metal findings on the back. The article I was following suggested epoxy...which didn't hold very long. No CA glue around back then other than the tiny bottles for re-gluing your rear view mirror back onto the windshield. I eventually tried Weldbond glue which dries clear and holds for years. I was not using any exotic wood so you will have to do some testing.