Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

laser rigs revisited

Posts

laser rigs revisited

#1

laser rigs revisited

Mike Foster

Well I looked at all the options and must say that both the Sinner and Monster rigs looked good. Both Jeff Willaford and Tony Wheeler gave me a heads up on a new laser rig that Jeff Salter has come up with. I got in touch with him and he emailed me some photos of his rig. I was instantly hooked. The attachment to my Jamieson D handle was simple and solid and the adjustment for positioning the laser was also simple and solid. But what really sold me was the rotation of the laser light offset about the set point. Hard to describe in words so I attached a couple of pics that Jeff sent me. I was going to take some photos of the rig, but didn't get around to it so I just used Jeff's.


I turned a HF yesterday and could not believe how nice this was to use, especially in comparison to my home-made job that was not user friendly. Generally I would have to stop and change the offset of my laser rig frequently to stay perpendicular with a tangent of the curve. If you don't, you would run the risk of a steadily increasing or decreasing wall thickness and possibly end up cutting air. Jeff has come up with a unique solution to this. All you have to do is set the laser, with no offset at the tip of your tool, dial in the offset for the wall thickness you desire, then rotate the head to stay perpendicular to the tangent. You don't have to remove the tool from the HF to change the angle, so it really speeds up the process. I also think it actually is more accurate and easier to get a nice smooth interior surface.

The laser that Jeff has used is a sealed laser. It looks similar to the ones used with the Monster and Sinner rigs, but he said he wasn't sure that it was the same. Batteries and switch is remotely located at the other end of the arm like both the other rigs.

I would post a pic of the HF, but it is sealed with Anchorseal as I left the walls about 1/2" with the intention of carving on it later. It was a blank of magnolia that I got in a trade with Donna Parrillo in RI.

I am not promoting Jeff's rig, just a happy customer. He stated that his first production run was 25 units, and he only has a few left. I think he is going to do a larger production run shortly.

Re: laser rigs revisited

#2

Re: laser rigs revisited

Jeff Willaford

Looks good Mike. Jeff had this at Hartford last year but did not have them in production at the time. Pretty neat idea I think.

Re: laser rigs revisited

#3

Steven Antonucci

Was this the thing he had at the Stubby booth?

steven antonucci

Bill showed it to me and a buddy. It looked "revolutionary" (pun intended).

:-)

Steve

Re: laser rigs revisited

#4

Re: Was this the thing he had at the Stubby booth?

Jeff Willaford

Close....

The rig Jeff was demoing at Hartford was Bill Rubenstein’s system. Bill's system includes the “D” handle, the tool gate and the laser. Jeff's rig is only the laser system from the clamp at the “D” handle up. Also the implementation of the laser alignment on his system is different than Bill’s.

Re: laser rigs revisited

#5

Re: laser rigs revisited

Mike from St. Clair Shores

Mike,

I also mentioned Jeff's laser rig in your earlier post. I just got home from a visit to Jeff's house where I had a nice visit and picked up 3 of his laser rigs. One for me and the other two for friends. I also have made my own for 3 different hollowing rigs, but they were not nearly as accurate as Jeffs. As a laser engineer, he has really put some thought into this. I'm glad you like it, I know I do.

Mike

Re: laser rigs revisited

#6

Re: laser rigs revisited

Alan Van Art

Are these being sold to the public at this time? Is there a website with more info/ordering info?