Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

forstner bits in a tailstock

Posts

forstner bits in a tailstock

#1

forstner bits in a tailstock

Darrin Hill

if you go to craft supplies and look at their eccentric chuck, there is a photo of inlaid or bored holes in the disk and then a smaller dowel is inserted...

i tried this, but my bit seems to go off center a bit and i get an offcenter hole..

any suggestions on what causes it and how to fix it?

I can see the bit wobble when trying to bore, so im pretty sure its on the tailstock end,....

Re: forstner bits in a tailstock

#2

Katherine Kowalski

Re: forstner bits in a tailstock

Katherine Kowalski

Darrin,

The secret is to NOT use a forstner bit. For inlays, I would use a negative-rake scraper, or parting tool, or bedan to cut the recess, (whichever you happen to have handy), then carefully make the recess cylindrical.

Katherine

Re: forstner bits in a tailstock

#3

Re: forstner bits in a tailstock

john lucas

I haven't had problems with Forestner style bits. You do need to start slow and let the bit center itself. It also helps any time you drill a hole, to make a divot in the center with another tool. I use the toe of the skew. It only needs to be very small. This helps the drill bit start on center. It's kind of like making a center punch mark in metal before drilling. It keeps the bit from wandering.

Katherine's method of using other tools to actually bore the hole is the most accurate way but you really have to sneak up on the size.

Re: forstner bits in a tailstock

#4

Re: forstner bits in a tailstock

Fred Holder

I use a Forstner bit in the tailstock quite a bit. Since very few lathes have a perfect alignment between tailstock and headstock. I turn on the lathe and bring the tailstock up until the point of the Forstner bit just touches the wood. I move it in slightly, if the point draws a circle around the center point, I back off the tailstock and stop the lathe. I then use a spring loaded center punch to punch a hole in the center of the circle. I then bring up the tailstock again and let the point of the Forstner slip into the center punch hole. Turn on the lathe, lock down the tailstock, and drill the hole. It has worked for me for several years now.

Re: forstner bits in a tailstock

#5

Forstner bits work very well, but they .....

JamieDonaldson

...must be sharp and the lathe must be in good alignment headstock to tailstock. A loose quill in the tailstock will also induce wandering as it is cranked into the wood.

Re: forstner bits in a tailstock

#6

Re: forstner bits in a tailstock

Dale Miner

My method is similar to John's, but I go a touch larger on the divot. I make a divot large enough that the spurs of the bit touch before the center point. Often, if the center point touches first, it will hit the grain in a spot that pushes the point to one side, and wobbling will result. When the spurs touch, there should be only one circle on the end of the piece. If there are two circles, then the bit is not hitting the center of the blank. This could be from a tailstock/headstock alignment issue, or it could be a result of a bent bit, or chucking inaccuracy. Regardless the source, I can usually make adjustments to some part of the system to bring the bit to dead center and start the hole. Snugging the quill lock a bit until the body of the bit is in the wood helps to keep the bit on center.

Even with the above, varying grain patterns and densities will cause the bit to track off center on a deep hole. If the hole needs to be dead centered and straight, then drilling undersize and turning to size is the best method.

Re: forstner bits in a tailstock

#7

Katherine Kowalski

One more thing...

Katherine Kowalski

One more thing I forgot to mention -- be aware that dowels are RARELY cylindrical. They often go oval depending on where they were cut from the tree. If you want a clean glue joint and your inlays to fit perfectly, you may have to turn your own dowels.

Katherine

Re: forstner bits in a tailstock

#8

She is so correct.

John Lucas

I started making my own dowels using a router and jig because I found out real quick that dowels are usually oval. The nice thing about making your own is you get to choose the type of wood and if your careful you can even choose the grain direction.

Re: forstner bits in a tailstock

#9

Mike Stafford

Nearly everything we turn is oval after a while...

Mike Stafford

Wood does not stay round for long despite our best efforts on the lathe. As soon as it is exposed to a drier or wetter humidity environment it is going to do what wood does- shrink or swell up. And when it shrinks or swells it is no longer going to be perfectly round.....

Re: forstner bits in a tailstock

#10

Re: One more thing...

Mike from St. Clair Shores

Katherine and John are both right in stating that dowels are often not round. When inlaying different color woods, I often use a plug cutter. The are very accurate.

Mike

Re: forstner bits in a tailstock

#11

Re: One more thing...

John Lucas

I take a lot of flak from a machinist friend when I use dial calipers to measure wood. He claims it won't stay that dimension for day. My response is, I put 2 pieces together as close as possible right now. Tomorrow they can move.

Plug cutters do work really well for our purposes but you have to know that some make tapered plugs. These are perfect for some applications and not so good for others. I have both straight and tapered plug cutters. If your inserting dowels into something that you aren't going to turn very much, like clock faces then the tapered plugs work great. If your going to be turning into the plugs such as angled holes so the plugs come out oval after turning, then you will see glue gaps where the tapered plugs don't fit all of the hole. In this case the straight plugs are better.

I was doing very long dowels in long holes and consequently had to make my own dowels so there weren't any glue gaps anywhere when I turned into them later during the project.