Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

internal hollowing light

Posts

internal hollowing light

#1

internal hollowing light

bernie feinerman

I thought I would start a new thread and not hijack Charlie's "Now I remember thread....."

http://www.onegoodturn.ca/pages/HollowingTools.html describes their hollowing tools and includes a 12 volt light kit to mount on the hollowing bar. They recommend using an 18 volt or 24 volt transformer instead of the 12 volt supply so as to get a brighter light inside of the hollowform. The kit looks like it is using a 12 volt car bulb which will generate heat (and a lot more heat & light at the higher voltages) but the light will be more diffuse than a laser.

HF used to sell a laser inspection light with a 12" flexible shaft between the LED's and the batteries.

Has anyone tried to put a light on the end of their hollowing tool/boring bar/etc.. to try to gauge the wall thickness and see inside the piece they were hollowing?

Bernie

Re: internal hollowing light

#3

Dick Hines

Re: internal hollowing light

dick hines

One of my fellow club members was talking about a inspection camera he picked up at a discount store for about $150. It has a light and a small camera for looking into tight spaces.

Re: internal hollowing light

#4

Re: internal hollowing light

bernie feinerman

That is a good writeup on making a hollowing light. Some questions....

Are you worried that the heat from the lamp may agravate the drying of the piece your hollowing and make it distort faster/more?

Do you get enough light output that you can judge the wall thickness as you are hollowing?

Bernie

Re: internal hollowing light

#5

Harry Robinette

Re: internal hollowing light

harry robinette

If your looking for being able to see the thickness of the walls Google Frank Sudal Woodturner Canada.

He pretty much started the light hollowing for the tall vases.I'm sure if Lyle Jameson sees this he nows about Franks process.

Re: internal hollowing light

#6

Re: internal hollowing light

Jim Pugh

Thank you Harry. I was going to suggest the same thing. Frank did all of this years ago. When he demo'd at our club he found that some of the bulbs he was using burned out quickly due to shock and found that spraying them with WD-40 prolonged their life.... Anyway, Frank died a few years ago so some searching for his information might be required.

Re: internal hollowing light

#7

Harry Robinette

Re: internal hollowing light

harry robinette

Jim your right I just spent 1 hour and could not find anything on his rig or the light system. I still use mine but it's been a while mostly I use the laser.I'll try to dig it up and take a photo of it.

Re: internal hollowing light

#8

Re: internal hollowing light

Doug Wolf

Bernie,

You asked:

Are you worried that the heat from the lamp may agravate the drying of the piece your hollowing and make it distort faster/more?

No. It might create some heat, but just spray the inside with water if it's getting too dry. Which is what I do even if I'm not using the light.

Do you get enough light output that you can judge the wall thickness as you are hollowing?

Yes. Just remember more light shines through the grain that is inline with the light.

Edit: Steve, I use it in the conditions in the first photo of my PDF write up but turn the two lights on the lathe off. There is still bright light coming in from the rollup shop doors but the 12 volt light still shines through the wood bright enough to see the thickness of the wood. Sorry no more pictuces than in the PDF. Doug

Re: internal hollowing light

#9

Steven Antonucci

Can you post a picture of it "in use"?

steven antonucci

I am interested in seeing how well it works with that little 12v bulb vs. a 100W on the outside (like I use with a hat). I am also interested to see if you use it in the dark or with the lights on...

I think light is a more accurate just of thickness than a laser because the laser beam is susceptible to vibrate and has some error built into it's fuzziness. I am mostly interested in this as an academic exercise, since I don't really care to produce 3' tall turnings that are 1/16" thick. I don't have anywhere to put stuff that big without the kids eventually destroying it.

S

Re: internal hollowing light

#10

Re: internal hollowing light

B. Leathers

Michele's(not sure of spelling)art's and crafts has sold a "Knit Lite".It's 9" long,plastic,battery powered led.It puts out a surprising amount of light but not enough to judge wall thickness.

Re: internal hollowing light

#11

Re: "the heebie jeebies" *LINK*

Henry (Raleigh, NC)

I not 1/4 the turner most of you gals/fellows (unless we go by body mass!), but much of what is proposed here gives me the "heebie jeebies." I would not even consider putting an incandescent bulb into a 'being turned' HF. Yeah I know what's being described is regulated down to 12 V and all, but I just can't see putting a fragile (GLASS) bulb, taping it to a metal shaft, supplying electrical power, and then inserting it all into an actively turned vessel.

I MIGHT consider an LED - at least that is solid state.

I would consider using a "light pipe;" a bundle of fiber optic strands. They are commonly used for microscopy; they have a very bright W-halogen bulb (like the old overhead projectors) and a controller to vary light intensity. Example Linked below.

My 2 cents.

Henry W


http://www.meijitechno.com/illuminators.htm

Re: internal hollowing light

#12

Re: internal hollowing light

Wally Dickerman

Apparantly no one here has seen Paul Fennell's very impressive demo on hollowing using an inside fiber optic light. Paul's been doing this for years with his thin walled pieces. I think that Paul even sells the unit that he uses. Check out his website. If you don't know who Paul is, he's one of the real masters of turning.

http://www.jpaulfennell.com/index.html

Re: internal hollowing light

#13

Re: internal hollowing light

John Lucas

I use a 12 volt tail light bulb with a transformer. The automotive bulbs are stronger and don't burn out due to vibration. I learned that from Frank Sudol.

I have never had even a remote chance of a fire. I've burned out a few when I was experimenting with different bulbs.

Re: internal hollowing light

#14

Re J. Paul Fennel tools

bernie feinerman

Thank you for the link to J. Paul Fennel's site. His fiber optic light is impressive but a little steep for a rank amateur. I will try an auto bulb since it is doable with a minimal outlay of $$.

The thickness calipers listed on his site looks like a good value.

Bernie

Re: internal hollowing light

#15

Harry Robinette

Re: internal hollowing light

harry robinette

I use the 12 volt auto bulbs also John,from Frank's design. My hollower is also one of Frank's Boring bar system. I use a model train transformer for a power unit. Have to make sure the transformer has a higher output then 12vdc. So you can run the bulb up to 18 to 24 vdc to get the brightness you need to see through the thin walls.