Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Project from you know where is done.

Posts

Project from you know where is done.

#1

Project from you know where is done.

john lucas

Here is the router plane with fixes in place. It came out quite nice. The top and bottom are turned on the after drilling all the holes and bandsawing out the rest of the shape. I turned a walnut plug for the 2 1/8" hole and then drilled it out to 2". I thought that and the walnut bottom came out quite well.

the cutter is a 3/8" allen wrench. It was a bear filing out the 6 sided hole in the thumbscrew to hold the wrench. I noticed this morning that I need to file one of the flats just a hair more. I actually have a blister on my middle finger from holding the small file.

the other tool is a socket chisel I picked up this summer. I cleaned all the rust off and built a rosewood handle for it. Calculating the taper for the socket was fun. I put drill bits in until I found one that exactly fit the bottom. then measured the depth. then I measured the big end and had the 3 dimensions I needed to turn it. It fit so well I simply dropped it in the hole and tapped the end with a mallet. I could not pull it back out so I left it.


Re: Project from you know where is done.

#2

Re: Project from you know where is done.

matt overton

Beautiful! Does it work as good as it looks?

Re: Project from you know where is done.

#3

Re: Project from you know where is done.

Galen Vetterick

You must never sleep to work on so many fine projects! Nice pair of hand tools.

Now that you blistered your fingers, a brass thumb screw, washer and wing nut would really look nice with the color of the wood. Brass thumb screw maybe too soft to hold the allen wrench "blade"?

Re: Project from you know where is done.

#4

Re: Project from you know where is done.

john lucas

I thought about making brass parts but this was really about building something from found or modified parts that the average woodworker could do. If I made one from scratch I would have used a square cutter like the traditional tools, then I would have made brass parts to hold everything with some brass Inlay.

Re: Project from you know where is done.

#5

Steven Antonucci

Why is the opening round?

steven antonucci

I knew what you were making, but I can't figure out why it was turned? wouldn't you want a small throat like any other plane?

Or did you turn it just because?

S

Re: Project from you know where is done.

#6

:-)

Opelika Edro

Some questions you already know the answer to before you ask them!

Re: Project from you know where is done.

#7

Nice job on the plane and beautiful chisel handle.

Opelika Edro

I know most of the work was in the router plane; I know it was challenging and your result is a nice piece of work. But the thing I can't keep my eyes off of is the chisel handle -- it's perfect, and it's gorgeous. I don't know if I could use a mallet on a chisel that looked so nice! (Did I mention the lines on that thing? And the ring? Sweet!)

So, what kind of finish did you use on those pieces? (And now I'm going back to make sure you didn't already say...)

Re: Project from you know where is done.

#8

Re: Why is the opening round?

john lucas

Steve all the router planes I've seen have large throat. I think it's because of the low cutting angle of the blade. Apparently you don't need a chip breaker. I was follow, more or less, plans that I saved from a magazine. I did pick up a Stanley router plane at the flea market this spring but it's missing some parts and I haven't had time to make them. My machining skills are coming along but if you remember how long it took to make your first bowl and how easy it is now, well that's where I am as a machinist. It takes me hours and hours to do the simple things because every step along the way is a learning curve.

Re: Project from you know where is done.

#9

Re: Nice job on the plane and beautiful chisel han

john lucas

I used spray lacquer. I was tired last night and lacquer is quick and a pretty decent finish. Usually on chisel handles I use an oil because they are going to take a lot of handling and abuse.

Re: Project from you know where is done.

#10

Is this for spindle or faceplate turning?

jake Niedling

:D :\ :b :)

Re: Project from you know where is done.

#11

Re: Why is the opening round?

Stuart Johnson

Steve, the blade on a router plane is more along the line of sliding a chisel along flat with the bevel up just clipping the high spots. The base of the plane prevents the blade from cutting deeper than you want. Having the large opening allows you to see just what is going on.

Re: Project from you know where is done.

#12

For roughing bowls of course.

john lucas

Re: Project from you know where is done.

#13

Re: Is this for spindle or faceplate turning?

Mike from St. Clair Shores

They are both very nice John, now get off that slippery slope or who knows where you will land. Now just keep repeating, I'm a woodturner, I'm a woodturner, I'm a woodturner. :)

Re: Project from you know where is done.

#14

Re: Is this for spindle or faceplate turning?

john lucas

Thanks Mike. I had this terrible urge to go plane a board flat. Now I'll just put it on the lathe and turn it flat.

Re: Project from you know where is done.

#15

Ellis Walentine

Awesome, dude

Ellis Walentine

I'm wondering what keeps the allen wrench vertical?

And, what's the theory on the end of the chisel handle sticking out of the schlag ring by that distance?

Nice job on both pieces, John.

Ellis

Re: Project from you know where is done.

#16

Re: Awesome, dude

john lucas

There is a thumb screw that holds the allen wrench. I filed a 6 sided slot in the thumb screw to hold the allen wrench. There is a slot carved in the large walnut hole so the thumb screw will seat far enough to clamp the allen against the walnut wall. This slot keeps it vertical.

Why is the allen so long. Well it doesn't have to be that long. You probably won't cut a dado more than 1/2 to 3/4" deep. I had originally thought I would thread the top of the allen and add a fine adjustment nut. I decided not to do that because if you adjust the cutter really deep the threads would be in the thumb screw which might be a little rough. so for now I'll just leave it like that.

Re: Project from you know where is done.

#17

Re: Project from you know where is done.

Dick Wilson

Thanks for the a solution to my problem John!!!! I have a vase that I want to do a band of alabaster inlay on. Can't turn it because the piece is slightly out of round with an 1/8" wall thickness. With my cruddy luck I would go the through the wall. I have a plain like this.......primarily used to plane out hinge pockets before routers were used. I can plane out a channel and do the inlay :-))))))))

Re: Project from you know where is done.

#18

Leo Cuellar

Re: Project from you know where is done.

Leo Cuellar

It is a great design, John. A very nice save of a project as well, which just gives it some character & attitude. Chisel looks "sharp" too.

Re: Project from you know where is done.

#19

Re: Project from you know where is done.

john lucas

You can. I would cut a groove all the way around first. Otherwise the blade will lift fibers up at the edges. you could probably cut the groove on the with the machine off. rotate the work by hand to draw the line and then do the same with either a saw or a razor knife.

Another option is to use a small router on a table mounted to the lathe. If you set up a depth stop on the router it will follow the contour of the bowl. I may have photos of this setup on my home computer. If not I can set it up and get a shot this weekend.

Re: Project from you know where is done.

#20

Re: Project from you know where is done.

john lucas

Chisel isn't sharp yet but it will be. I ground it but haven't flattened the back or hit the bevel with the diamond hones.

Re: Project from you know where is done.

#21

Re: Project from you know where is done.

bill Crommett

John: I am jealous. Your home brew projects always turn out so beautiful but mine turn out crude as crude even if they sometimes work satisfactorily.