Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

New tools I made

Posts

New tools I made

#1

New tools I made

John Lucas

I'm doing a tool making demo for a flat woodworking club. I've needed a marking knife and a carving gouge that fits the size between 2 of my smaller ones so built those two. Then I decided I needed a scratch awl so I built that.

I used tool steel for the blades and brass screw on to sweat on copper pipe adaptors for the ferruls. The brass fittings turn very nicely with the Thompson tools. In fact I was able to turn the wooden handles after turning the brass without ever sharpening the tool.

Re: New tools I made

#2

Steven Antonucci

How did you grind the gouge?

steven antonucci

I want to make a few, but I haven't come up with a way to mill the flutes that cleanly. Lots of filing and sanding?

S

Re: New tools I made

#3

Nice looking tools...

GaryG in MD

John, When you're turning brass, what kind of cut(s) do you use? Push? Pull? Shear? Shear scrape? What seems to work best? At what level do you start sanding? etc... Just curious... ...Gary

Re: New tools I made

#4

Re: New tools I made

matt overton

I think those flatwork guys are in for a treat. Beautiful work, John

Re: New tools I made

#5

Re: New tools I made

Mike Brazeau

Very nicely done John. You mentioned a skew you hade made from a 3/8 or 1/4" spade bit the other day. Do you have a photo of that by any chance?

Re: New tools I made

#6

Steve Kubien

Nicely done

Steve Kubien

Very nice work John. Now, what is this "flat woodworking" you speak off? Is that for those who use the big table with the motor in their shop for something other than turning blank storage?

Re: New tools I made

#7

Leo Cuellar

B-E-A-Utiful.

Leo Cuellar

Nice work all the way around, John.

Re: New tools I made

#8

Alan Zenreich

Re: Nicely done

Alan Zenreich

Steve,

I have it on good authority that flatworkers produce shelves on which we place turnings.

Re: New tools I made

#9

Re: How did you grind the gouge?

john lucas

Start with a triangular file. This helps you center the groove. Then switch to various round files. For bigger gouges I flatten the steel (hot of course) and then form it over a round bar. Then I go to the files and sandpaper wrapped around dowels or drill bits.

Re: New tools I made

#10

Re: Nice looking tools...

john lucas

I use the tools in a cutting method, bevel rubbing, just like in wood. On rare occasions I use it scraping. It's all about rubbing the bevel and not forcing the cut. I can typically start sanding with 220 if I've done it successfully. Occasionally a metal won't cut clean and I have to scrape.

Re: New tools I made

#11

Very nice looking tools!!

Mike from St. Clair Shores

Re: New tools I made

#12

Steve Kubien

Re: Nicely done

Steve Kubien

Well, at least they're doing something worthwhile. :)

Re: New tools I made

#13

Re: New tools I made

john lucas

Here is a photo of the tip along with my other tools I use for ornament finials.




Re: New tools I made

#14

Re: Nicely done

john lucas

Steve I have one of those powered tables. I use it to make photos of my work.

Re: New tools I made

#15

Very nice work-as usual!

Don Orr

Re: New tools I made

#16

Katherine Kowalski

Re: New tools I made

Katherine Kowalski

Those are some seriously beautiful tools, John.

Katherine

Re: New tools I made

#17

Re: New tools I made

Mike Brazeau

Thanks a bunch John.