Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Epoxy Help Please

Posts

Epoxy Help Please

#1

Epoxy Help Please

Dick Wilson

I want to do an a piece that will take a considerable amount of epoxy. I have used System Three in the past and it is a great product......it is also quite expensive. I know there are other manufacturers out there who make/sell epoxy that is much more reasonable in $$$$.

What epoxy do you use and where do you get it? Thanks for helping. Dick

Re: Epoxy Help Please

#2

Re: Epoxy Help Please *LINK*

Dave Paine

I think all epoxies are not cheap. Price is linked to the cost of oil, like many other things.

West is a good product. You did not state what functionality is needed for the epoxy - weather resistance, heat resistance, water resistance.

I do not use a lot of epoxy so I purchase products which are non-critical mixes like the Lee Valley products. Some products require exact measurements.


http://www.leevalley.com/US/wood/page.aspx?p=20011&cat=1,110,42965&ap=1

Re: Epoxy Help Please

#3

Re: Epoxy Help Please

john lucas

Dick Depending on what your doing you might want to consider casting resin's. They are very clear compared to many epoxies. It turns well. I have not used it to bond things together so I don't know how well it does that but if you want to fill anything or cast things like Pens it is great.

Re: Epoxy Help Please

#4

Re: Epoxy Help Please

Dick Wilson

I guess I should have described in more detail. I want to thicken epoxy with filler, color it, and inject it into voids between the wood pieces. It is not used as a finish or a "glue" per se.

Re: Epoxy Help Please

#5

Re: Epoxy Help Please

Bill Jacksonville, NC

Any inexpensive epoxy should do what you need. Depending upon thickness may take a day or two to fully harden.

Re: Epoxy Help Please

#6

Re: Epoxy Help Please *LINK*

john lucas

Dick You will need to play. Thickening epoxy changes it characteristics. I have had it turn to almost foam when I added too much thickener. There are several types of thickener that West system sells. I have found the 407 to be the best for what we do.

You can color it with India inks or Latex artist colors. Use as little as you need to color it because these also affect how hard it is when it dry's, how well it glues, and how it sands etc.

I can't say enough about running tests. It changes viscosity as it starts to harden so if you mix it up like toothpaste it will be thinner as it starts to heat up. I have found creating a dam of some with tape or clay is about the best way to contain it.

Another alternative is Inlace. You can get Inlace in lots of premixed colors. They also have colored chips and powdered metal that you can add. The nice thing about Inlace is it gets thick really quick. You can mix it and then stir it until it starts to thicken. Then pack it in the gap. Do this quickly because once it starts to gel it goes fast. I buy mine from www.turtlefeathers.net


http://www.turtlefeathers.net

Re: Epoxy Help Please

#7

Re: Epoxy Help Please

Mike from St. Clair Shores

Dick,

I just attended a one day seminar with Marilyn Campbell yesterday.She is the most knowledgeable person I know when working with epoxy. I'm sure if you wrote her she would answer all your questions. She uses the west systems 205 and 105. For the filler she uses 410 micro crystalline. The filler doesn't make it foam up, you just can't pour it over a half inch deep at a time. Over a half inch deep you need to pour several layers. She uses oil base paint in a tube like artists use. She is doing hands on today and tomorrow at the Michigan Woodturners. After her class yesterday, most of the comments were that it was one of the best classes that most of the turners ever attended.

Re: Epoxy Help Please

#8

Re: Epoxy Help Please

Mike Johnson

I have had good luck with Raka epoxy. Their web site is www.raka.com, and they sell the resins and various fillers that work well for filling voids in lumber.

Re: Epoxy Help Please

#9

Re: Epoxy Help Please

Dick Wilson

Mike, Darn it. You were at the demo in Holy Saturday? So was I. Fat guy with the tan cap. Would have liked to meet ya. The process she uses with syringes is the process I have been looking for to use on a hollow form I want to do. The reason for my question is that I think it is going to take a lot of epoxy and West System is expensive.....

Re: Epoxy Help Please

#10

Re: Epoxy Help Please

Dick Wilson

Mike, Thanks, I will take a look at it.

Re: Epoxy Help Please

#11

(Message Deleted by Poster)

Dick Wilson

Re: Epoxy Help Please

#12

Re: Epoxy Help Please

John Lucas

Dick It is expensive but it goes a long way. I found that you can buy it from some local (or in my case not so local but not horribly far) source you can avoid the rediculous shipping rates. You may be limited in the filler you can buy from local sources.

I'll have to go back and look at my notes on the fillers. I bought 406, 407 and 410. They all work, they just have different characteristics for sanding and filling.

Re: Epoxy Help Please

#13

Re: Epoxy Help Please

Barry L Elder

Hi Dick,

RAKA is a neighbor of mine and sells excellent products but they are expensive. When I use his products I thin with Xylol (10%) to help release the air bubbles. It can be colored with artist paints, inks, and dyes. Possibly other things but those are all I've tried. Good Luck!

Re: Epoxy Help Please

#14

Re: Epoxy Help Please

Dick Wilson

Barry, thanks for the info. Great info when I do a "pour" particularly regarding the air bubbles. This piece I want to use a syringe to inject expoxy into large openings on a round surface. I would be using filler to make epoxy the consistency of mayonaise.

Re: Epoxy Help Please

#15

Re: Epoxy Help Please

Chuck Engstrom

A couple of more tidbits:

Use syringes (ask your vet for a pair) to measure small quantities and you will save a lot of waste. I can reliably mix 0.6 cc resin with 0.3 cc hardener for products that mix 2:1 like System 3 Clear Coat. West System loves for you to use a whole squirt from their generous pumps when only a little dab is needed, and their mix is (I think) 5:2 to make the issue even more challenging.

Recently I coated an end-grain goblet with epoxy and later put it in a sort of warm place to speed up the chemical process. What I got was a bunch of bubbles when air in the pores expanded in the warmth and came to the surface. By the time I noticed this my coating had gotten pretty well along in hardening and I had to sand the bubbles off later. Perhaps if you warm the workpiece before coating, you'll get the reverse effect of drawing the epoxy into the grain as the wood cools before the epoxy hardens.

One of our members likes stuff by www.rotdoctor.com, which he tells me is very thin and very slow to cure so that it will sink in deeply in rotted/spalted wood with full effect, which might take as long as a week. Not cheap at all but if that's what you need it may be worth knowing about.

Best to all--

Chuck

Re: Epoxy Help Please

#16

Re: Epoxy Help Please

John Lucas

I use electronic scales to measure the quantites. It's very easy and quick. I do use the squirt pumps on the west system but for smaller quantities the scales work great.

Re: Epoxy Help Please

#17

Re: Epoxy Help Please

Mike from Saint Claire Shores

Dick,

I have used epoxy from Blehm Plastics for over 10 years. I never used it with a filler though.

They used to be just around the corner from my woodshop so it was very convenient.

I used to buy it in quantity and get a much better price. Then divide it up with club members.

They are now in Indiana. They are a big automotive supplier. I'll include a link to thier website.

Mike

www.blehmplastics.com

Re: Epoxy Help Please

#18

Thanks Everyone

Dick Wilson