Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

unscientific poll

Posts

Re: unscientific poll

#26

Re: unscientific poll

robo hippy

I almost never use a face plate. Most of my pieces are utility bowls, sawn parallel on a big bandsaw, and circle cut on a small bandsaw. I did use a face plate on a 22 inch bowl I did. Couldn't get it in position on my drill press for a forstner bit and drilling a recess. I did use a big recess though on the bottom. Jaw and chuck size should be appropriate for the size of piece you are turning. For a NE piece, I have used a face plate to drill a flat spot for mounting a face plate.

I seldom use the tailstock as well. There has been a trend for chuck manufacturers, and on the lathes to extend more away from the headstock for clearance for turning the outside of a bowl that has been reversed. Since I turn green to final thickness, this isn't necessary for me. When I reverse, the outside is done. Larger pieces will vibrate some because of this extension. With my 3520 A, this was almost never a problem. I did use my tailstock on my big bowl above.

I do have one set of chuck jaws that have some dings in them from early learning with the McNaughton. Still in good enough shape that I don't need to true them up, which can be done with a scraper, and small (1/16 inch) shim between closed jaws. I have completely taken a chuck completely apart, as I broke some teeth off the pinion gear, and the gear that the jaws are on. This happened on one chuck a couple of times. Craft Supplies told to send it back, and I did. No problems since then. I have also taken them apart to clean finish off them. Wire wheel on a small grinder do a good job.

robo hippy

Re: unscientific poll

#27

Re: unscientific poll

Don Orr

No-I don't turn very large pieces, and rarely use faceplates.

Yes-always.

Yes.

Yes.

Yes-as needed. I don't lube though-maybe a little wax. I try to keep my chucks clean first though.

Re: unscientific poll

#28

Keith Tompkins

Re: unscientific poll

keith tompkins

Thanks for all the responses, Yes...some of my questions were an afterthought, but still related. Thanks again.

Re: unscientific poll

#30

Yes To ALL!

George Guadiane

Re: unscientific poll

#31

Yes to all.

Mike Rubes, Apex, NC

Re: unscientific poll

#32

Joe Fleming

no yes yes yes yes

Joe Fleming

Re: unscientific poll

#33

Yes to all

Colin

Re: unscientific poll

#34

Re: unscientific poll

Ed Larson

Rarely turn large pieces or use a faceplate

Yes

Yes

No

No

Re: unscientific poll

#35

Yes to all

Barbara Gill

Re: unscientific poll

#36

Re: Yes to all

bill Crommett

Yes, Yes, Yes. and NO,NO.

Re: unscientific poll

#37

Keith Tompkins

Re: unscientific poll

keith tompkins

Hi Dennis, I've seen chuck jaws so worn they wouldn't hold a tenon securely. The ridges in the One-Way chuck jaws were rounded over and no longer crisp. Others were beat with a chisel trying to get stripped screws out. Some had dings on the back side that prevented them from seating properly in the chuck.All still being used.

Re: unscientific poll

#38

Re: unscientific poll

George Van Beynen

Yes to all but the faceplate. I have a strong homemade drive spur I use one the Drive spindle and of course support with the tailstock.

Re: unscientific poll

#39

Steven Antonucci

Re: unscientific poll

steven antonucci

I raised the question on a previous post...Do you use a faceplate when mounting large or unbalanced work?

(Sometimes, depending upon what I am making)

Do you bring up the tailstock as a precaution?

Always

Do you use a larger set of jaws in your chuck for large pieces?

I use the biggest set that I have, and would use a bigger set if I had one.

Do you inspect/replace worn jaws on your chuck?

Jaws don't get worn in my shop, but they occasionally lose the battle with one of Doug Thompson's tools and need to be refiled or replaced. I have replaced one set, one time.

Have you ever disassembled and lubed your chuck?

Yes, one a year at least