Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

1st Jr Gent pen from my shop

Posts

1st Jr Gent pen from my shop

#1

1st Jr Gent pen from my shop

Andy Lincoln,in Dearborn MI

Hi All,

After dinner I was able to head to the shop and make a pen from some blanks I had epoxied the day before.I have been acquiring pen kits and blanks at an alarming rate as of late so today's lesson was to turn a pen in a style/kit I had not used before.

I had recently ordered some Jr Gent kits and had a nice turquoise colored acrylic blank as my project.My wife is a fan of turquoise so this pen was made to be a gift to her.


I encountered a problem when I went to trim the barrel the sleeves/cutters that I have did not have a diameter that matched the larger,cap end brass tube.I do not have a disc sander that is reliable/accurate enough to consider a squaring jig,the table has WAY too much flex to ever be accurate.Anyone have a suggestion on what method I should seek?


The pen was sanded to 400 with standard sandpapers and then polished thru the grits ,wet with micro mesh.I am happy with the outcome,I would just like to have a consistent trimming/sanding method.

Thanks,

Andy

Re: 1st Jr Gent pen from my shop

#2

Re: 1st Jr Gent pen from my shop

David Walser

Andy,

That's a very nice pen. The Jr Gent is one of my favorite kits. I'm sure your wife will cherish hers.

As to your question about how to square the ends of the pen blanks, you have two choices:

* The first choice would be to beef up your disk sander's table and use it. That, in the long run, may be your best choice. You'll learn that some types of pen blanks cannot be squared up using a pen mill. (The mill will chip out the blank rather than cut it cleanly.)

* The second choice is to take a cheap pen blank and prepare it as if you were going to make a slim line pen -- including gluing in the brass tubes. After the glue has set, mount the blank on you pen mandrel and turn the blank down until it fits slides inside of the brass tube from your Jr Gent kit. Then, use the newly made bushing with your standard pen mill to square up the ends of your kit blanks. Or, you can go to Arizona Silhouette and buy the pre-made bushings for your pen mill.

Neither of these choices do anything about the dried on glue that may have set up inside your pen blank's tubes. For that, I try to find a twist drill bit that can serve as a reamer to clean out the glue.

HTH

Re: 1st Jr Gent pen from my shop

#3

Re: 1st Jr Gent pen from my shop

Mike from St. Clair Shores

Andy,

First that is a very nice looking pen. Secondly, you could always make a disc sander that requires a faceplate and some mdf or a similar material. You can buy sanding discs with adhesive backs in many sizes. 7" is my choice. After you screw the mdf to a faceplate, mount it on your lathe and turn it to a 7 inch diameter. Then stick the sanding disc to the mdf. All you need to do now is make a table that either sets on the ways or fits in the toolrest. It's a nice sander to take for demos also.

Good luck,

Mike

Re: 1st Jr Gent pen from my shop

#4

Re: 1st Jr Gent pen from my shop

Jim Swank

Try slipping a sierra style bras tube over the shank on a sierra mill. It's not perfect, but may be close enough.

Re: 1st Jr Gent pen from my shop

#5

Re: 1st Jr Gent pen from my shop

Don Evans

A trick I have used is to find a drill bit that fits the tube without cutting it. Grind down the end of it so it will fit in the end mill. This is good for the end mills that take 7mm barrels, there was one end mill, sold by Craft USA that took a much smaller shaft, if you have that one, I don't know if you could grind it down that far successfully.

If you want to try this, grind with light press turning the bit constantly as possible, it doesn't have to be perfectly round. Just be mentally prepared to go slow while doing it and you should get good results.

Don

Re: 1st Jr Gent pen from my shop

#6

Jim in Burlington Ont.

Re: 1st Jr Gent pen from my shop

Jim in River Oaks, Ont.

Very nicely done Andy,

I am sure your wife is very happy with the pen you made for her.

I think you have some great advice from others on the mill solution. I make sleeves to fit mills I already have, size them up to the tube size I am trying to square, it's simple and is essentially cost free.

Take care,

Jim

Re: 1st Jr Gent pen from my shop

#7

Re: 1st Jr Gent pen from my shop

Philip F. Duffy

Having experienced frustration with pen mills in the past, these days I chuck up the blanks and true up the ends down to the brass. Careful application of a sharp roundnosed scrapper or a 1/4in spindle gouge will result in a perfectly squared off end. Just be sure to use the 60d. live center when you first mount the blank in the chuck. That holds both ends true on the brass. Yes, it consumes some extra time but I need not worry about a loose looking final fit on parts. Phil