Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

new term for teaching rubbing the bevel

Posts

new term for teaching rubbing the bevel

#1

new term for teaching rubbing the bevel

john lucas

Yesterday I was talking to a friend who called because he was having trouble controlling the bowl gouge. You know how we always talk about rubbing the bevel. It harder to get them to understand that the bevel points where the tool will go. Students want to push or pull the gouge in the direction they want it to go instead of controlling the angle the bevel to make it go where you want it.

I asked him to think of it as a tiller on a boat. Simply pull or push the handle to steer the bevel and make the boat go where you want it to go. He called back later to say that it worked.

I'm thinking about putting making a stick with a sort of T mounted to the bottom. This way I can show how when you move the T down the bowl if you lift the handle one way it will lift the front edge (and of course stop cutting) and if you move the handle the other way it will make the front edge dig in or cut deeper. do you think that will help people understand how the bevel works.

Re: new term for teaching rubbing the bevel

#2

If you rub the bevel, do you get 3 wishes?

jake Niedling

Re: new term for teaching rubbing the bevel

#3

Re: new term for teaching rubbing the bevel

Emmett Manley, Lakeland, TN

The boat tiller analogy would have been more confusing to me -- you pull the tiller to the left and the boat goes to the right. Perhaps some other terminology to replace bevel and rubbing the bevel, as "cutting line" or "cutting support?" Supporting the cut and directing the cut are important concepts and not intuitive to the new turner.

Re: new term for teaching rubbing the bevel

#4

Chuck Jones - West TN

How about a bench chisel and a board?

Chuck Jones - West TN

If you try to shave a thin slice of wood with a bench chisel with the bevel up, it's not so easy. Turn the chisel over and rest it on the bevel and it works much better.

Re: new term for teaching rubbing the bevel

#5

Re: new term for teaching rubbing the bevel

Dick Coers

Oversize visual aids always seem to help. I made a couple for demonstrating proper sharpening techniques of bench tools and hand planes, so they can understand the need for sharp intersecting surfaces. Soren Berger used the visual aid of sharpening pencils when teaching at our club. That seemed to make an impression with all the guys. Bring the bevel off the pencil and you don't control the chip, cut from the point up and has chip out, etc........ Nothing will replace making chips and mentoring.

Re: new term for teaching rubbing the bevel

#6

Re: new term for teaching rubbing the bevel

John Altberg

John,

I tried this exact same analogy with my son yesterday while teaching him how to rub the bevel. Unfortunately I never taught him how to sail, so my explanation resulted in a blank stare and further discussion about how a tiller and rudder work. Lesson learned: inquire FIRST about one's maritime experience before using this particular example!

Re: new term for teaching rubbing the bevel

#7

Re: new term for teaching rubbing the bevel

Jennifer Indy.USA

John, I usually tell students the importance of rubbing the bevel, but as you know if the flute isn't pointing in the direction of the cut things aren't going to go very well. I can be rubbing the bevel but if I have my flute pointing in the opposite direction I want to go that's not going to work very well. I make it a point to make sure they understand that the bevel rubbing and the flute pointing in the direction of the cut both work together to make the gouge work the way it should. I do like the relation to the boat though. A visual totally unrelated to the tool often times works wonders. I use the face of the clock visual a lot in my classes.

Jen

Re: new term for teaching rubbing the bevel

#8

While you are at it...

mjonesrdg

...you might try to come up with another visual for "turning downhill". Watching Jimmy Clewes and a few others teach cutting 'with', rather than 'against' the grain even when that cut looked like uphill to me was always confusing. If cutting 'steps' when roughing the form, I would think that cutting 'down the stairs' would make sense. Similarly, a "downhill" type running back on a level football field still amuses my missus. How do I explain that?

Re: new term for teaching rubbing the bevel

#9

interesting responses- I like Jake's best

john lucas