Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Debating a fundamental change around the lathe

Posts

Re: Debating a fundamental change around the lathe

#26

Re: The space above it...

woodspinner

Stuart : I've also seen that somewhere but don't know where.

Steve: The more weight you put up by the head the less vibration you'll have !!

: The more weight you put down low the more it helps with stability of the lathe.

: You have to watch weight up high because you can get the lathe unstable and large pieces can

cause the lathe to get VERY tippy.

My General 160 was a 12" lathe,I made it into an 18" lathe so doing this changed the height and caused both vibration and stability problems,I have a #300 box on the end for vibration and #240 on the shelf for stability.

Hope this helps.

Woodspinner

Re: Debating a fundamental change around the lathe

#27

Leo Cuellar

Re: Not Mark's idea, but

Leo Cuellar

Thanks for the info, Mark. Fabbed up some parts tonight, and should be able to try it out this weekend.

Leo

Re: Debating a fundamental change around the lathe

#28

Fabbed

Mark Mandell - Gone Round In Jersey

Hi Leo,

Hope it does as well for you. Just remember that the connection to the lathe bed seems to be very important as that's the point of maximum stress on the post. The post assembly needs to be very stiff, I suspect to transfer as much of the "wiggle" up to the weight. I used a piece of 4" lolli welded to a 3/8" plate, plus a 3/8" draw plate under the bed, and a 1/2" hex bolt between them. That locked things down tight. (Sorry, no pix) You also want to make sure that the weight is "inside" the lathe's footprint so you don't have the tail getting "light" in its contact with the floor.

I had an idea to replace the sand bag with a round cast concrete block with a hollow core that would slip down onto the top of the post. Never got around to trying it because I bought my Stubby and sold the JET before I went that far.

Re: Debating a fundamental change around the lathe

#29

Re: Immediately SHOT DOWN!

Carole Valentine

Seems like a whole lot of trouble to me. I just let the shavings build up under the lathe shelf until no more will fit. My toes bury into them nicely and they keep my feet warm. :D Of course as those who have visited will attest...I am definitely not a neatnik when it comes to my shop (or anything else for that matter!)

Re: Debating a fundamental change around the lathe

#30

Steven Antonucci

Until you realize you are 4" taller

steven antonucci

and you are holding your tools down by your knees :)

I am actually trying to muster up the thought of moving the lathe to another area of the shop and containing the mess... but like you, I only clean when I have to...

It's been all winter.

I have to...soon.

Steve

Re: Debating a fundamental change around the lathe

#31

Leo Cuellar

Stubby? Only in my wildest dreams!

Leo Cuellar

Thanks for the additional info, Mark. My plan is to bolt the mount (4 - 1/2" bolts) just under the bed, at the top of the legs. I know its not ideal, but I can't tighten down my head stock if I slide it forward (poor engineering). That is something I can deal with if my idea doesn't work. The lathe is bolted to the floor, but I had planned to add some ballast at the tail as disaster insurance, and start off small on the weight. I'm not doing any large diameter work other than 16" platters until I get a larger lathe. Additionally, I'm taking Terry Scott's idea a little further and am building a special jaw for my chuck that I can bolt a counter weight to for my eccentric pieces.

Leo

Re: Debating a fundamental change around the lathe

#32

Dreams *LINK*

Mark Mandell - Gone Round In Jersey

If I hadn't an uncle who passed with no heirs, I'd still be dreaming, myself. :D

You may wish to go to John's new site and communicate with him directly as to suggestions for your application. I notice that his "new" General doesn't have a post and block attached.


John Williams

Re: Debating a fundamental change around the lathe

#33

Barry, have you photos to share?

Opelika Edro

Re: Debating a fundamental change around the lathe

#34

Re: Battery????

Don Evans

Hey Steve:

Didn't read all the remarks but this is second time I've seen that battery under the lathe!

I know it is great for weight BUT what is those bare terminals get shorted some how?

Or something knocks a hole in it?

At least protect the terminals for short from something getting across them, but better fine something else for weight and put battery in box or something somewhere else.

Don

Re: Debating a fundamental change around the lathe

#35

Here you go...

Barry Irby


As you can see it is pretty utilitarian. Built out of scraps and left overs.

The top is 44 X 19" and 2" thick. The "blank" under the head stock is a column of sand and there is a tray under the top and in the toe kick.

On a different note, I bout the lathe primarily as a bowl lathe. Later I was asked to turn some table legs for a family member and bought the extension. On the advice of Tim Geist, the then current Teknatool Rep I just bolted it onto the end of the ways and left it completely unsupported. Odd looking but it seems to be fine. Its been there for about five years.

Not shown in the picture is a roll of lead flashing someone gave me. Its about three inches in diameter and weighs about a hundred pounds. Its laying on the back of the top next to the wall. That seemed to be the final note in settling things down.

Also note how clean and well organized my shop is. Everyone should be at least this orderly. :)

Re: Debating a fundamental change around the lathe

#36

Leo Cuellar

Better than I'd hoped for.

Leo Cuellar

Mark, I just finished preliminary testing. The results are very promising, I'd say about 80% of the vibration is gone. Here are a couple of pics of the rough assembly.



I decided I'd attach it the way you did, bolted to the ways (guess I can live with a bent handle on the lock after all). Picked up a few additional parts to accomplish that. Have some more drilling to do.



I have to weld all the fittings together and add gussets to make sure it stays put. I also have to turn & attach the platform to the faceplate the bucket sits on. 40lbs of sand & 25lbs of lead shot in the bucket. The only flex is at the point where it sits on the bed. That should go away once it is securely bolted.

Decided to use the tee fittings to make it easier to run wiring for additional lighting later & hanging accessories.

Leo

Re: Debating a fundamental change around the lathe

#37

Gussets Are Good

Mark Mandell - Gone Round In Jersey

Your "Plumber's Solution" :D is going to have a fair amount of flex in that smaller diameter pipe you're using, so make sure you get things rigid. Flex in the assembly will diminish the damping effect, although how much I can't tell you; mine was a straight-up rig.

Glad it's helping. I'll let john know his baby lives on. :)