Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Henry Taylor Decorating Elf *LINK*

Posts

Henry Taylor Decorating Elf *LINK*

#1

Henry Taylor Decorating Elf *LINK*

john lucas

I know it sounds like a joke but it's a pretty cool tool. Looks like it uses Dremel or other HSS 3/32" shaft tools. I can't tell for sure. Watch all 4 videos. It takes a while but is quite interesting. Micheal Mocho will probably get one and be an expert in nothing flat. I'll probably try my hand at building one.


http://www.youtube.com/results?search_query=nick+agar+decorating+elf&aq=1

Re: Henry Taylor Decorating Elf *LINK*

#2

Re: Henry Taylor Decorating Elf..Thanks!

mjonesrdg

I looked for a US "stockist" to no avail...wonder what the retail cost might be?

Re: Henry Taylor Decorating Elf *LINK*

#3

Bill Blasic

Re: Henry Taylor Decorating Elf..Thanks!

Bill Blasic

Packard Woodworks $59.95 and the two extra cutters $8.95 each. It is a neat little tool.

Bill

Re: Henry Taylor Decorating Elf *LINK*

#4

Re: Henry Taylor Decorating Elf

Phil Powell

So John, Will you be making your own set of these tools? Then demoing them?

Re: Henry Taylor Decorating Elf *LINK*

#5

Re: Henry Taylor Decorating Elf

John Lucas

Phil I was thinking last night. I have Foredom handpieces and I'll bet I could remove them from the flex shaft, put a bit in them and so the same thing he's doing with that fancy handle.

I assume there are a couple of bearings and a magnet in the bottom to keep the bit in place. With the Foredom handpiece the but would be captured and would be a little harder to swap bits but not enough to worry about. I'll try it this week and see. I need a short break from working on the house. Between building the shelves for my son, finishing the drywall in the new Dormer, and ripping out the floor in the old house I've been a little busy.

Re: Henry Taylor Decorating Elf *LINK*

#6

Re: Henry Taylor Decorating Elf

Phil Powell

A ball cutter in a foredom hand piece is just what I was thinking. I was messing

with the idea earlier this morning. As for the point tools I have several pieces of 1/4 HSS rod to make them out of. Something to do taday.

Re: Henry Taylor Decorating Elf *LINK*

#7

Re: Henry Taylor Decorating Elf

John Lucas

His point tool has a much sharpen angle than any I have seen. I'm going to make a new one that has that angle. A Tip. When grinding it's hard to maintain the 120 degrees between each face. I'm not sure it's critical but here's a method I learned to nail it every time. Grind a small flat area on the shaft. Now put a hex nut on the shaft and fasten it with a set screw mounted through the side of the hex. Lock the nut on the shaft so the hex screw is on the flat you ground. Now you lay this on the tool rest of your grinder with one flat side of the nut down. Grind that angle. Flip to tool for every other flat on the hex and you have ground 3 perfect angles on the tool.

Re: Henry Taylor Decorating Elf *LINK*

#8

Re: Henry Taylor Decorating Elf

Harry in Beautiful Downtown Kulpsville

John, an easier way than that. Get a brass plumbing fitting at the Borg. I think it is called a compression nut. Use it as the ferrel on the tool's wooden handle. Presto, more flats than you need. When sharpening just use every other flat on the grinder's tool rest.

Re: Henry Taylor Decorating Elf *LINK*

#9

Re: Henry Taylor Decorating Elf..Thanks!

Woodie49

Also http://www.woodturnerscatalog.com/ should have then in stock any day.

Re: Henry Taylor Decorating Elf *LINK*

#10

todays play with a knock-off Elf

mjonesrdg

Using a couple of Dremel spiral cut burrs in a rotary tool hand-piece, Hunter carbide cutter for coves, and the pointy end of a skew, I reasonably replicated the Elf patterns and played all day with varying presentations, cove sizes, stains, etc. Thanks again John Lucas, for giving the heads-up on the videos. After watching them last night, the learning curve was very short. This decorating method may be very useful to me to cover up some screw-ups in the future!