Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Chainsaw sharpening revisited

Posts

Chainsaw sharpening revisited

#1

Chainsaw sharpening revisited

Mike Foster

I just saw a rerun of the This Old House segment that showed the 5 second chainsaw sharpening running the saw. I got to thinking about this while on a snowshoe walk with the dogs today. I didn't see a close up of the rig they put on the chainsaw, but there seems to be only 2 ways for the system to work. One is by sharpening the top plate of the tooth, the other by sharpening the side plates. I can't fathom how they could use the system to sharpen a chain in the conventional method. Either of the the above methods would have a really limited life of the chain, and I think could actually become dangerous. If you are sharpening the top plate or side plate, they can only get thinner each time the chain is sharpened. Eventually, it seems to me, they can get thin enough to pose the risk of flying metal fracturing while using the chain.

While sharpening a chain in 5 seconds is attractive, I think sticking with conventional sharpening is fast enough and far more controllable (and safer) than this method.

I confess to having, and loving, an Oregon power chain grinder that the lawn mower services use. If you pay attention to the angles, dress the stone right and take off only the metal you need to get it sharp, these are much faster and more consistent than sharpening by hand. They will also sharpen the chain evenly so you don't get the saw wanting to make curved cuts. It's another tool for you tool junkies, and really nice to have if you work with the chainsaw a lot.

Re: Chainsaw sharpening revisited

#2

Re: Chainsaw sharpening revisited

woodspinner

Mike

From what I've heard and seen I'm with you,I use my Dermal saw sharpening jig.If you use it right and go easy it works great and I don't cut in circles ether.

Re: Chainsaw sharpening revisited

#3

Re: Chainsaw sharpening revisited

Joe Herrmann

If the saw sharpening method in question is the same one I saw, I was intrigued to say the least. I did a little research on it and discovered that it doesn't use a conventional chain. Along with the sharpening device, you have to purchase a special chain where the teeth are configured a little differently.

Re: Chainsaw sharpening revisited

#4

Dick Hines

Re: Chainsaw sharpening revisited

Dick Hines

One of the guys in My club bought one of the sharpening systems. The teeth look like a string of skews attached to a chain.

The sharpner system will only work on Oregon chains and bars.

Re: Chainsaw sharpening revisited

#5

Re: Chainsaw sharpening revisited

Woodchuck

I also recommend the Dremel. It's the best of about 6 systems I have tried. Gets the chain razor sharp in a short while.

Re: Chainsaw sharpening revisited

#6

Re: Chainsaw sharpening revisited

Scott Crumpton

I use the EZE-Lap sharpeners between trips to the Harbor Freight chain grinder. Works well for me, though the grinder is less than optimal.

http://www.eze-lap.com/product/chainsaw.htm

No affiliation to EZE-LAP.

---Scott.

Re: Chainsaw sharpening revisited

#7

Completely different Chain, here's a link *LINK*

Barry Irby

Here's a link to it. Bailey's has them. It appears to cut entirely differently. I would like to hear from someone who has one and uses it.

There's a video.


http://www.baileysonline.com/itemdetail.asp?item=ORFPS55

Re: Chainsaw sharpening revisited

#8

That's Not All

Mark Mandell - Gone Round In Jersey

You'll also need the special bar ($40) and you'll be limited to 16" on most saws (a couple of 18") from what I've seen. I also checked and it appears that the sharpener does not grind the depth gauges, so you're still going to be working the file on those.

Re: Chainsaw sharpening revisited

#9

Craftsman tried it in 1977 *LINK*

Dick Coers

Here is a link to a Craftsman saw that had it in 1977. They called it self sharpening and had the stone back in the housing. As far as I'm concerned, not worth the engineering that went into it. Where does the grit go that wears off the stones? My guess is under the chain into the groove of the bar. Good design if you are selling bars!


http://books.google.com/books?id=suIDAAAAMBAJ&pg=PA71&lpg=PA71&dq=craftsman+self+sharpening+chain+saw&source=bl&ots=_BVQi-Uiq_&sig=CjJP04gXYU-wboIgXkEw43zuQnc&hl=en&ei=kYtYTfnKC4zVgAfJpcmaDQ&sa=X&oi=book_result&ct=result&resnum=8&ved=0CEUQ6AEwBw#v=on

Re: Chainsaw sharpening revisited

#10

Re: Craftsman tried it in 1977

Frederick Nelson

McCullach also tried the "self-sharpening" system in their 300 series saws back in the late seventies. The system required a chain with completely different geometry compared to what we are used to using. The chain cut with a "bevel-down" configuration, rather than the more conventional "bevel-up" tooth with depth gauge or limiter.

Fred

Clear and a lot warmer in Eastern Missouri

Re: Chainsaw sharpening revisited

#11

Chuck Jones - West TN

You can't beat this sharpening tool!

Chuck Jones - West TN

http://www.google.com/products/catalog?q=chainsaw+file&oe=utf-8&rls=org.mozilla:en-US:official&client=firefox-a&um=1&ie=UTF-8&cid=10057393441835283001&ei=JaNYTYT-LMWblgeY0ayWBw&sa=X&oi=product_catalog_result&ct=image&resnum=1&ved=0CC8Q8gIwAA#

or here

http://www.grainger.com/Grainger/NICHOLSON-Chain-Saw-File-4PKE7

It is a little pricey, but well worth the investment. :)

Re: Chainsaw sharpening revisited

#12

Jesper, Denmark

Re: If I may parafrase old Mayor Dailey of Chicago

Jesper, Denmark

File early and file often.

A file claw that holds the saw on a piece of log in the woods and filing the saw as soon as you notice any deterioration in performance is the key. Then it only takes a few strokes on each tooth, and you are back in business.

Leave it too long, and it then becomes a major sharpening job.