Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Bench Grinder????

Posts

Re: Bench Grinder????

#26

Re: Diamond Dresser

Jim Tusant

John, do you feel this dresser is better than the Wolverine Dressing Jig by Oneway or are they about the same????

Re: Bench Grinder????

#27

Lyle Jamieson

Re: Bench Grinder????

Lyle Jamieson

I think it is one of those times when you get what you pay for. When you pay more you get better tools...usually. With that said I don�t think your vibration is caused by your grinder, or the grinding wheels. Usually vibration is caused by the wheels wobbling. With the grinder off put your finger up next to the side of the grinding wheel. Spin the wheel by hand and watch the wobble. The hard part it getting the wobble to stop. Loosen the grinder arbor nut and move the grinding wheel, twist it on the shaft to a different place. Tighten the wheel nut and test again. It will likely be still wobbling. Repeat above, and again repeat, repeat, repeat. Are you getting discouraged yet?? After many tries, you will get lucky and the wheel will run true and the vibration will stop, keep trying.

Re: Bench Grinder????

#28

Re: Diamond Dresser

john lucas

Personally I like it better but both are good. Before I got either one I made my own and played with the single point diamond dresser. I found that I had more control of the single point diamond tool when I fed it across the stone at an angle. The oneway jig feeds the diamond across perpendicular to the stone while the Gieger feeds it at an angle. I think this is better but in reality it's hard to tell the difference in the final condition of the stone.

Re: Bench Grinder????

#29

Bill Blasic

Re: Diamond Dresser

Bill Blasic

In my case the wheels were out of round front to back and side to side didn't enter into the equation. I was using the stone grader on the wheel and wondered why after sharpening the tool would not cut. I actually made the first dresser out of wood with a 1/2" single point diamond. The wheel was almost 3/32" out of round and after using the diamond the grinder actually ran very smooth and my tools began to cut wood. I ran into a bunch of dressers on EBAY and bought them all as they were like my wooden designed one except made of metal. You should use this type with the diamond point cutting below center pointing down. This serves two purposes, if you got too aggressive you would not get a catch that might hurt you and the wheel and by pointing down you keep the diamond with a pointed shape. :)

Bill

Re: Bench Grinder????

#30

Re: Diamond Dresser *LINK*

Doug Trembath

The first single point dresser I encountered was the one that came with the Tormek. I suppose the others work in a similar fashion, and probably very well. I have used the handheld dresser I got from CSUSA in the 90's, along with the Norton SG wheel, and feel it is really a fine tool for wheel maintenance. The pairing of the SG wheel and this dresser solved a lot of grinding problems for me at the time, and I have helped a lot of novice turners with balancing and truing their own grinders resulting in much better performance and improvement in their work, as well. It's hard to get a good, smooth profile when the gouge is bouncing on the wheel, as we all know.

You can actually vary the wheel's effective grit with it, true the outside diameter to help balance the grinder, and provide an excellent grinding surface very quickly with just a bit of patience and understanding.

Mike Mahoney showed me that if you approach the wheel with it and push a bit harder and move across the wheel quickly, you can make it coarser grit, about 80, and if you very lightly touch the wheel, moving slowly, you can grade the wheel up to about 200 grit. I find this very helpful in grinding and honing tools, including tools other than turning tools. I use the same grinder for my hand tools and it works very well, although sometimes I think I'd do better with a 6" wheel for chisels and plane blades for hollow grinding.

There's a link to the one I use below, if anyone's interested. I haven't needed anything else since I got this one, but what works for some doesn't always work for others.

Doug Trembath


Diamond Dresser